Difference between revisions of "Add Jtag Port"

From NAS-Central Buffalo - The Linkstation Wiki
Jump to: navigation, search
Line 82: Line 82:
 
The same page also contains the [http://www.genbako.com/jtag/kuro-jtagcable.png schematics], some pictures of the assembled jtag cable and software needed. This cable can be used without adding the additional components.
 
The same page also contains the [http://www.genbako.com/jtag/kuro-jtagcable.png schematics], some pictures of the assembled jtag cable and software needed. This cable can be used without adding the additional components.
  
According to http://www.abatron.ch/Files/ManAccessCOP-2000C.pdf the following pins are used for a PPC COP/JTAG interface:
+
According to http://www.abatron.ch/Files/ManAccessCOP-2000C.pdf and http://www.freescale.com/files/soft_dev_tools/doc/user_guide/CWH-UTP-UG.pdf the following pins are used for a PPC COP/JTAG interface:
 
{|  
 
{|  
 
|- bgcolor=#CCCCCC
 
|- bgcolor=#CCCCCC
Line 108: Line 108:
 
|
 
|
 
|8
 
|8
|NC (RxD)
+
|CKSI
 
|- bgcolor=#CCCCCC
 
|- bgcolor=#CCCCCC
 
|TMS
 
|TMS
Line 114: Line 114:
 
|
 
|
 
|10
 
|10
|NC (TxD)
+
|??
 
|- bgcolor=#CCCCCC
 
|- bgcolor=#CCCCCC
|SRESET (Neg)
+
|SRST (Neg)
 
|11
 
|11
 
|
 
|
 
|12
 
|12
|Gnd
+
|Gnd (??)
 
|- bgcolor=#CCCCCC
 
|- bgcolor=#CCCCCC
|HRESET (Neg)
+
|HRST (Neg)
 
|13
 
|13
 
|
 
|
Line 128: Line 128:
 
|NC (key)
 
|NC (key)
 
|- bgcolor=#CCCCCC
 
|- bgcolor=#CCCCCC
|CKSTP_OUT
+
|CKSO
 
|15
 
|15
 
|
 
|
Line 137: Line 137:
 
  Pin Name      Description
 
  Pin Name      Description
 
   1  TDO        JTAG Test Data Out
 
   1  TDO        JTAG Test Data Out
   2  QACK      ??
+
   2  QACK      Not Needed
 
   3  TDI        JTAG Test Data In
 
   3  TDI        JTAG Test Data In
 
   4  TRST      JTAG Test Reset
 
   4  TRST      JTAG Test Reset
   5  HALTED    ??
+
   5  HALTED    Not Needed
 
   6  Vcc Target 1.8 – 5.0V:
 
   6  Vcc Target 1.8 – 5.0V:
 
                 This is the target reference voltage. It indicates that the target has power and it is also used
 
                 This is the target reference voltage. It indicates that the target has power and it is also used
Line 149: Line 149:
 
                 limiting resistor between this pin and the target Vdd, it should be 100 Ohm or less.
 
                 limiting resistor between this pin and the target Vdd, it should be 100 Ohm or less.
 
   7  TCK        JTAG Test Clock
 
   7  TCK        JTAG Test Clock
   8  <reseved>
+
   8  CKSI      Not Connected ??
 
   9  TMS        JTAG Test Mode Select
 
   9  TMS        JTAG Test Mode Select
 
  10  <reseved>
 
  10  <reseved>
Line 156: Line 156:
 
  13  HRESET    Hard-Reset
 
  13  HRESET    Hard-Reset
 
  14  <reseved>
 
  14  <reseved>
  15  CKSTP_OUT  ??
+
  15  CKSO      Not Connected on the 8421
 
  16  GROUND    System Ground
 
  16  GROUND    System Ground
  

Revision as of 14:51, 31 May 2006

This document is a work in progress. It explains how to fit the internal on-chip debug (OCD) port on a Linkstation, Kuro-Box or Kuro-Box/HG to a PC interface.

Cable required: msp430-jtag.jpg

Contents

OCD connector

The internal OCD port uses an electrical standard known as JTAG/COP. The signals have to be buffered to protect the hardware from damage and we use a JTAG wiggler to do this.

Those with some electrical experience could build their own circuit, but most will opt for ordering one.

Schematics and Software to build your own

http://hri.sourceforge.net/tools/

Buy one

Commercial The Macraigor Wiggler seems to be the cheapest at $150.

Hobby Could the 20-pin Olimex ARM-JTAG be modified to work with Kuro-Box? $20.

Locate the pads

The pads are labelled CN5 and can be seen just above the serial level converter (where the yellow, orange, and red wires start to split) in this photo

Connector Pin-outs

In order to use this port, you should add the 10K series VIO resistor R67 and a 4-way 1K resistor pack at RA11. It may be possible to use some functionality without these components.

If you know which set of pin-outs that LinkStation/Kuro-Box uses, please update this page with the details.

According to Baulab the following pins are identified

TDO 1 2 ?
TDI 3 4 ?
? 5 6 ?
TCK 7 8 ?
TMS 9 10 ?
? 11 12 ?
Vcc 13 14 ?
? 15 16 Gnd


The same page also contains the schematics, some pictures of the assembled jtag cable and software needed. This cable can be used without adding the additional components.

According to http://www.abatron.ch/Files/ManAccessCOP-2000C.pdf and http://www.freescale.com/files/soft_dev_tools/doc/user_guide/CWH-UTP-UG.pdf the following pins are used for a PPC COP/JTAG interface:

TDO 1 2 QACK
TDI 3 4 TRST (Neg)
HALTED 5 6 Vcc Target
TCK 7 8 CKSI
TMS 9 10 ??
SRST (Neg) 11 12 Gnd (??)
HRST (Neg) 13 14 NC (key)
CKSO 15 16 Gnd
Pin Name       Description
 1  TDO        JTAG Test Data Out
 2  QACK       Not Needed
 3  TDI        JTAG Test Data In
 4  TRST       JTAG Test Reset
 5  HALTED     Not Needed 
 6  Vcc Target 1.8 – 5.0V:
               This is the target reference voltage. It indicates that the target has power and it is also used
               to create the logic-level reference for the input comparators. It also controls the output logic
               levels to the target. It is normally fed from Vdd I/O on the target board.
               3.0 – 5.0V:
               This input is used to detect if the target is powered up. If there is a current
               limiting resistor between this pin and the target Vdd, it should be 100 Ohm or less.
 7  TCK        JTAG Test Clock
 8  CKSI       Not Connected ??
 9  TMS        JTAG Test Mode Select
10  <reseved>
11  SRESET     Soft-Reset
12  GROUND     System Ground
13  HRESET     Hard-Reset
14  <reseved>
15  CKSO       Not Connected on the 8421
16  GROUND     System Ground