From NAS-Central Buffalo - The Linkstation Wiki

Revision as of 16:26, 18 August 2007

Introduction

Note

The same instructions will work for a KuroBoxPro

What you can do with serial access on a LS Pro

At first: check serial access In fact you can control the UBoot Bootloader.

• You can change to EM Mode at will without any dirty tricks.
• You can look at the linux system of your LS pro without having to flash any custom firmware
• You can load a kernel + ramdisk via tftp
• Hey! We connect it because we can!

Serial access isn`t that important for users, but it is very important for developers because they
exactly see what is happening while the LS Pro boots.
The kernel log tells us a little more about the hardware and it allows us to debug a newer kernel.
Without serial that is not possible.

Why it is easy to gain serial access on the LS Pro

Pinout - Ground is on the Right side

Project of creating ready2use serial cables

Anyone who wants a cable please add his name to the lists below.

Here some pictures from the build-process (mindbender had fun with it)

I opened all FutureDial Cables to check if all cables used the same color-coding + Profilic-Chip:


Prebuilt cables will use a heat-shrink-tube to make the cables more stable.

The Serial Converter

The serial port signals from the processor are only 3.3V. For proper RS-232 12V signaling, an RS-232 level shifter needs to be added. These are very common in PDA serial cables also, but can be purchased

Models other than KuroPro

If you are attaching a serial header pin onto the main board, you may want to consider: Using the header pin unit with a 90 degree bend, or you might not be able to close the case Soldering it with the pins toward the interior, rather than toward the case. This allows easier access, since if the pins face the case side they would be very close to the metal side. This would make access is so tight that one might end up taking the board out to get plug fitted on the pins.

Build your own LVTTL/RS232 or LVTTL/USB interface

• LVTTL/RS232 - Building a Custom Serial Interface
• LVTTL/USB - Use a Nokia Serial Cable on an ARM9 Linkstation
• LVTTL/USB - Use a cheap phone sync cable with the serial port

Buy your own TTL Level Shifter

• LVTTL/RS232 - MAX232 based from Futurelec - MINIRS2323V
• LVTTL/USB - FTDI chip based cable - TTL-232R-3V3

Usage considerations for the TTL-232R-3V3

TTL-232R-3V3 USB to TTL Serial Converter Cable A very similar TTL/USB converter cable that uses a chip by FTDI (the same chip is used in the SCON-KIT ) can be obtained, but the pinout at the connector end would need to be reassigned: Spec Sheet w/ pinout, wire colors & other info Mouser Part # 895-TTL-232R-3V3 $20.00 Mouser Part # 517-929400-01-04 $0.32

A working/tested pinout/wire-color scheme is: Color Pin Number Signal yellow 1 TXD orange 2 RXD unused 3 VCC black 4 GND

• Solder the 4-pin header to the board. Make sure you don't have shorts.
• You will need to switch wires on the TTL-232R-3V3 cable. Use a sharp object to lift the plastic tabs and carefully pull the wires out. Rearrange them according to the table above (black, empty, orange, yellow, empty, empty) and slide those wires back in. Tape the other wires to make sure they don't short anything.
• When plugging in the cable, make sure black aligns with GND, yellow with TXD, and orange with RXD.
• Connect the USB cable to your computer, start a terminal program with the right settings.
• Turn on the device, you should see output from the bootloader in couple seconds.

Using a USB Plug to form a friction-fit connector

WARNING! I blew out a fuse on my KuroBoxPro by using this method, consider soldering in a serial port header instead Ramuk 18:13, 18 August 2007 (CEST)

1) You will also need an old USB-plug (Female, Type A). I used two from USB-extender-cables and the rest from female-USB-connectors that i directly ordered in a shop.
2) you will also need something as thick as 1 mm. This can be wood, plastic or the latest flyers you collected by going out at the weekend. We used a Eurocard which we broke in Pieces (4 rows * 9 holes)

Prepare the USB-Plug

Indifferent which way you use, you will have to make the usb-plastik part a little smaller....you also will have to get rid of all parts so that it looks like the next picture.

If you are using one from an extender cable

Best would be to use a grinder. Do not hesitate to destroy the cables. It is recommended to remove everything so that you can solder the cables from the phonesync-cable directly to the pins.

If you have bought the part directly

Just open the metal-case and use a grinder to make it look like the picture above. You won`t have to remove any glue or cables.

Checking the cable/plug

Best with a Voltmeter. To go completely safe test from the pins for the yellow (TX) + orange (RX) wires. The green one + shield (GND) can be tested from the pin on the other side.

Pin  Signal orange Transmit (TX) yellow Receive (RX) Power (3.3V)* Green + shield Ground (GND)

(in this case from on top of the profilic chip).

Using superglue

Have fun!

Cable is confirmed to work...here, hyperterminal is used in WinXp