|LinkStation Live™ with BitTorrent|
|CPU||88F5182 266Mhz Clock Speed|
|RAM||128Mb, on to blocks NANYA NT5TU32M16AG-3C|
|internal HDD|| 1TB Model has a Samsung F1 DT HD103UJ, with 32MB Cache, 7200RPM Sata disk
other disks found are:
|Fan||one in the case|
|GPL Kernel||mainline support, enable gpio_fans module|
|Hardware Hacks||Possible hack allowing addition of a USB-B port, allowing device to act as a USB gadget. Kernel modules incomplete.|
Buffalo LinkStation Live is a Network Attached Storage built in DLNA Server, desined for home networking to share your documents, pictures, movie and music over a network.
You can store contents from network computers or using the one touch direct copy function, that is a means of taking pictures or movies from your digital camera, camcorder and storage device via USB port directly. Stored data can be shared on your network and a built-in DLNA media server can stream it to a PC, a MAC, a Buffalo LinkTheater an other DLNA CERTIFIED™ entertainment devices. Our Web Access feature enables you to access your data and media stored in the LinkStation via the interenet by computuers and iPhone's. With a built-in BitTorrent Client, LinkStation can download content without the requirement to keep your PC powered up.
Intelligent Power Saving functions, timer power on/off and auto power on/off with your Windows PC all help towards power saving and eco in mind.
- With Web Access you can store, share and access files from any web browser
- Use Web Access for iPhone to access the digital library on your LinkStation
- Built-In Media Server connects to DLNA compatible digital entertainment devices
- One touch transfer of media files from digital camera/camcorder with Direct Copy feature
- Seamlessly integrates with iTunes® 7 and allows you to access your music files on the LinkStation from your iTunes software
- Supports Apple Time Machine
- Built-In BitTorrent Client
- Eco Friendly Power Saving Mode (PC Interlocking Power System/Schedule Power Management System)
- Built-in print server to print documents from anywhere on your network (*1)
- Easy setup does not require drivers
- Supports UPS connectivity via USB port
- Expand storage by adding a USB 2.0 hard drive
- Includes Memeo™ AutoBackup Software for Windows or Macintosh
- 10/100/1000 Gigabit Ethernet with JumboFrame support
- Access your data from any Windows or Macintosh computers
- Can't use stock distro, use Debian
- After compiling the kernel with ls-chl support and appropriate modules, run the following commands:
devio > foo 'wl 0xe3a01c0B,4' 'wl 0xe3811061,4' cat foo arch/arm/boot/zImage > zImage.new mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n 'linux' -d zImage.new uImage.buffalo
- For correct fan support, the gpio-fan module needs to be enabled and the following script, or similar, set to run on startup:
#! /bin/bash # # fan-temperature control daemon - fannydee # # this script checks the hdd temp on any LS-PPC that is running avr_evtd # and has hddtemp installed. If the temperature is greater than the # defined limit, it kicks the fan up to high speed. # # After the checkperiod elapses, it checks again. If the temperature is # below that limit, then it drops it back to low speed. # # # In /etc/fannyd.conf, mak sure you define your devices that you want to check the temperature on # e.g. /dev/hda or /dev/sda , the temperature limit, time check, etc. # You can declare more than one hard drive, but that is not a likely situation. source /etc/fannyd.conf HDDT=/bin/hddtemp while : ; do for A in $DEVICES ; do TEMPERATURE=$($HDDT -n $A) if [ $TEMPERATURE -gt $TEMPLIMITONE ]; then if [ $TEMPERATURE -gt $TEMPLIMITTWO ]; then if [ $TEMPERATURE -gt $TEMPLIMITTHREE ]; then echo 5000 > /sys/class/hwmon/hwmon0/device/fan1_target sleep 40 else echo 3250 > /sys/class/hwmon/hwmon0/device/fan1_target sleep 40 fi else echo 1500 > /sys/class/hwmon/hwmon0/device/fan1_target sleep 40 fi else sleep 60 # overcompensate w/ 1 min of extra fan time echo 0 > /sys/class/hwmon/hwmon0/device/fan1_target fi done done exit 0
- Sample /etc/fannyd.conf
# config file for fan-temperature control daemon - fannydee # # After the checkperiod elapses, it checks again. If the temperature is # below that limit, then it drops it back to low speed. # # Define your devices that you want to check the temperature on # e.g. /dev/hda or /dev/sda # You can declare more than one, but that is not a likely situation. DEVICES=/dev/sda # # define the timelimit in seconds. It is suggested to use a value # around 300 to 600 seconds # CHECKPERIOD=600 # # define a temperature limit at which you want the fan to kick up at # a good value is around 38C. Yes, use celsius. TEMPLIMITONE=35 TEMPLIMITTWO=40 TEMPLIMITTHREE=44
- buffalo-technology.com: LinkStation Live™ with BitTorrent
- pcconnection.com: LinkStation Live LS-CHL Shared Multimedia Storage
- The Buffalo NAS hacking Forums: LS-CHL LinkStation Live
- LinkStation Pro™ LS-XHL, a scaled-up version with more RAM (256MB) and a faster CPU
- LinkStation Live™ LS-CHL, a faster CPU (600MHz) but less RAM
Pages in category "LS-CHL"
This category contains only the following page.