Category:LS-QVL

From NAS-Central Buffalo - The Linkstation Wiki
Revision as of 07:10, 23 December 2012 by Shonk (Talk | contribs)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search
LinkStation Pro Quad LS-QVL/R5


LinkStation Pro Quad LS-QVL/R5
Machine Feroceon-KW (Kirkwood)
Board MVLSQV-BA
CPU Marvell 88F6282 1.6GHz (arm5te)
RAM 256MB
Flash ROM 512KB SPI flash
Other
NIC Marvell Alaska 88E1318 Gigabit Ethernet
USB 2 x USB 2.0 HiSpeed
internal HDD Varies
IDE/SATA Controller Marvell 88SM4140 Serial ATA II 1:4 port multiplier
Drive Capacity 2TB, 4TB, 8TB, 12TB
Fan
initial Networkname LS-QVL... (last 3 are the end of the MAC address)


Contents

cpuinfo

  root@Nas:~# cat /proc/cpuinfo
  Processor       : Feroceon 88FR131 rev 1 (v5l)
  BogoMIPS        : 1599.07
  Features        : swp half thumb fastmult edsp
  CPU implementer : 0x56
  CPU architecture: 5TE
  CPU variant     : 0x2
  CPU part        : 0x131
  CPU revision    : 1
  Hardware        : Feroceon-KW
  
  Revision        : 0000
  Serial          : 0000000000000000


meminfo

  root@Nas:~# cat /proc/meminfo
  MemTotal:         248468 kB
  MemFree:            3172 kB
  Buffers:          182272 kB
  Cached:            12368 kB
  SwapCached:            0 kB
  Active:            29188 kB
  Inactive:         201428 kB
  Active(anon):      13344 kB
  Inactive(anon):    22988 kB
  Active(file):      15844 kB
  Inactive(file):   178440 kB
  Unevictable:           0 kB
  Mlocked:               0 kB
  SwapTotal:       1000428 kB
  SwapFree:        1000428 kB
  Dirty:             21164 kB
  Writeback:          9984 kB
  AnonPages:         35988 kB
  Mapped:             7076 kB
  Slab:              11420 kB
  SReclaimable:       4948 kB
  SUnreclaim:         6472 kB
  PageTables:          524 kB
  NFS_Unstable:          0 kB
  Bounce:                0 kB
  WritebackTmp:          0 kB
  CommitLimit:     1124660 kB
  Committed_AS:      77696 kB
  VmallocTotal:     385024 kB
  VmallocUsed:       17544 kB
  VmallocChunk:     360444 kB


fdisk

  root@Nas:~# fdisk -l
  
  Disk /dev/sda: 500.1 GB, 500107862016 bytes
  255 heads, 63 sectors/track, 60801 cylinders
  Units = cylinders of 16065 * 512 = 8225280 bytes
  
     Device Boot      Start         End      Blocks  Id System
  /dev/sda1               1       60802   488386583+ ee EFI GPT
  
  Disk /dev/sdb: 500.1 GB, 500107862016 bytes
  255 heads, 63 sectors/track, 60801 cylinders
  Units = cylinders of 16065 * 512 = 8225280 bytes
  
     Device Boot      Start         End      Blocks  Id System
  /dev/sdb1               1       60802   488386583+ ee EFI GPT
  
  Disk /dev/sdc: 500.1 GB, 500107862016 bytes
  255 heads, 63 sectors/track, 60801 cylinders
  Units = cylinders of 16065 * 512 = 8225280 bytes
  
     Device Boot      Start         End      Blocks  Id System
  /dev/sdc1               1       60802   488386583+ ee EFI GPT
  
  Disk /dev/sdd: 500.1 GB, 500107862016 bytes
  255 heads, 63 sectors/track, 60801 cylinders
  Units = cylinders of 16065 * 512 = 8225280 bytes
  
     Device Boot      Start         End      Blocks  Id System
  /dev/sdd1               1       60802   488386583+ ee EFI GPT


mdstat

  root@Nas:~# cat /proc/mdstat
  Personalities : [linear] [raid0] [raid1] [raid6] [raid5] [raid4]
  md2 : active raid0 sdd6[3] sdc6[2] sdb6[1] sda6[0]
        1893871616 blocks super 1.2 512k chunks
  
  md1 : active raid1 sdb2[5] sda2[4] sdc2[2] sdd2[3]
        4999156 blocks super 1.2 [4/4] [UUUU]
  
  md10 : active raid1 sdb5[5] sda5[4] sdc5[2] sdd5[3]
        1000436 blocks super 1.2 [4/4] [UUUU]
  
  md0 : active raid1 sdb1[1] sda1[0] sdc1[2] sdd1[3]
        1000384 blocks [4/4] [UUUU]
  
  unused devices: <none>


dmesg output

  root@Nas:~# dmesg
  command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,12M panic=5 BOOTVER=0.26 mtdparts=nand_mtd:0x1000000(boot),0xfe800000(rootfs),0x800000(reserve)
  PID hash table entries: 1024 (order: 10, 4096 bytes)
  Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
  Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
  Memory: 256MB = 256MB total
  Memory: 235776KB available (4972K code, 271K data, 152K init, 0K highmem)
  Hierarchical RCU implementation.
  NR_IRQS:128
  Console: colour dummy device 80x30
  Calibrating delay loop... 1599.07 BogoMIPS (lpj=7995392)
  Mount-cache hash table entries: 512
  CPU: Testing write buffer coherency: ok
  xor: measuring software checksum speed
     arm4regs  :  1376.000 MB/sec
     8regs     :  1102.000 MB/sec
     32regs    :  1236.000 MB/sec
  xor: using function: arm4regs (1376.000 MB/sec)
  NET: Registered protocol family 16
  Feroceon L2: Enabling L2
  Feroceon L2: Cache support initialised.
  
  CPU Interface
  -------------
  SDRAM_CS0 ....base 00000000, size 256MB 
  SDRAM_CS1 ....disable
  SDRAM_CS2 ....disable
  SDRAM_CS3 ....disable
  PEX0_MEM ....base e0000000, size 128MB 
  PEX0_IO ....base f2000000, size   1MB 
  PEX1_MEM ....base e8000000, size 128MB 
  PEX1_IO ....base f2100000, size   1MB 
  INTER_REGS ....base f1000000, size   1MB 
  NFLASH_CS ....base fa000000, size   2MB 
  SPI_CS ....base f4000000, size  16MB 
  BOOT_ROM_CS ....no such
  DEV_BOOTCS ....no such
  CRYPT_ENG ....base f0000000, size   2MB 
  
    Marvell Development Board (LSP Version KW_LSP_5.1.3_patch13)-- MVLSQV  Soc: 88F6282 A0 LE
  
   Detected Tclk 200000000 and SysClk 533333333 
  MV Buttons Device Load
  Marvell USB EHCI Host controller #0: c8040800
  PEX0 interface detected no Link.
  PEX1 interface detected no Link.
  PCI: bus0: Fast back to back transfers enabled
  PCI: bus1: Fast back to back transfers enabled
  bio: create slab <bio-0> at 0
  SCSI subsystem initialized
  raid6: int32x1    146 MB/s
  raid6: int32x2    175 MB/s
  raid6: int32x4    169 MB/s
  raid6: int32x8    153 MB/s
  raid6: using algorithm int32x2 (175 MB/s)
  NET: Registered protocol family 2
  IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
  TCP established hash table entries: 8192 (order: 4, 65536 bytes)
  TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
  TCP: Hash tables configured (established 8192 bind 8192)
  TCP reno registered
  NET: Registered protocol family 1
  Trying to unpack rootfs image as initramfs...
  rootfs image is not initramfs (no cpio magic); looks like an initrd
  Freeing initrd memory: 12288K
  rtc mv_rtc: rtc core: registered kw-rtc as rtc0
  RTC registered
  MICON ctrl (C) BUFFALO INC. V.1.00 installed.
  Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.1.00 installed.
  Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
  Kernel event proc (C) BUFFALO INC. V.1.00 installed.
  initial_polarity_val = 0x03030000
  initial_polarity_val_high = 0x0001710c
  Buffalo GPIO SATA Hotplug Event Driver (C) BUFFALO INC. Ver.1.00 installed.
  XOR registered 4 channels
  XOR 2nd invalidate WA enabled
  cesadev_init(c000fd64)
  MV Buttons Driver Load
  VFS: Disk quotas dquot_6.5.2
  Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
  JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
  fuse init (API version 7.12)
  SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
  SGI XFS Quota Management subsystem
  msgmni has been set to 484
  alg: No test for cipher_null (cipher_null-generic)
  alg: No test for ecb(cipher_null) (ecb-cipher_null)
  alg: No test for digest_null (digest_null-generic)
  alg: No test for compress_null (compress_null-generic)
  alg: No test for stdrng (krng)
  alg: No test for hmac(digest_null) (hmac(digest_null-generic))
  async_tx: api initialized (sync-only)
  Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
  io scheduler noop registered
  io scheduler anticipatory registered (default)
  Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
  serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
  console [ttyS0] enabled
  serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
  brd: module loaded
  loop: module loaded
  Integrated Sata device found
  mvSataInitAdapter : regVal changed(0x00000010)
  IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
  scsi0 : Marvell SCSI to SATA adapter
  scsi1 : Marvell SCSI to SATA adapter
  ** BUFFALO Disable Command Queuing Function [0 0] **
  scsi 0:0:0:0: Direct-Access     SAMSUNG  HD502HI          1AG0 PQ: 0 ANSI: 5
  scsi 0:0:1:0: Direct-Access     SAMSUNG  HD502HI          1AG0 PQ: 0 ANSI: 5
  scsi 0:0:2:0: Direct-Access     SAMSUNG  HD502HI          1AG0 PQ: 0 ANSI: 5
  scsi 0:0:3:0: Direct-Access     SAMSUNG  HD502HI          1AG0 PQ: 0 ANSI: 5
  sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
  sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
  sd 0:0:0:0: [sda] 0-byte physical blocks
  sd 0:0:1:0: [sdb] Sector size 0 reported, assuming 512.
  sd 0:0:1:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
  sd 0:0:1:0: [sdb] 0-byte physical blocks
  sd 0:0:0:0: [sda] Write Protect is off
  sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
  sd 0:0:2:0: [sdc] Sector size 0 reported, assuming 512.
  sd 0:0:2:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB)
  sd 0:0:2:0: [sdc] 0-byte physical blocks
  sd 0:0:3:0: [sdd] Sector size 0 reported, assuming 512.
  sd 0:0:3:0: [sdd] 976773168 512-byte logical blocks: (500 GB/465 GiB)
  sd 0:0:3:0: [sdd] 0-byte physical blocks
  sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
  sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
  sd 0:0:2:0: [sdc] Write Protect is off
  sd 0:0:2:0: [sdc] Mode Sense: 23 00 00 00
  sd 0:0:1:0: [sdb] Write Protect is off
  sd 0:0:1:0: [sdb] Mode Sense: 23 00 00 00
  sd 0:0:0:0: Attached scsi generic sg0 type 0
  sd 0:0:1:0: Attached scsi generic sg1 type 0
  sd 0:0:2:0: Attached scsi generic sg2 type 0
  sd 0:0:3:0: Attached scsi generic sg3 type 0
  Loading Marvell Ethernet Driver:
    o Cached descriptors in DRAM
    o DRAM SW cache-coherency
    o 2 Giga ports supported
    o Single RX Queue support - ETH_DEF_RXQ=0
    o Single TX Queue support - ETH_DEF_TXQ=0
    o Receive checksum offload supported
    o Transmit checksum offload supported
    o Network Fast Processing (Routing) supported - (Disabled)
    o Driver ERROR statistics enabled
    o Driver INFO statistics enabled
    o Proc tool API enabled
    o SKB Reuse supported - (Disabled)
    o SKB Recycle supported - (Disabled)
    o Gateway support enabled
       o Using Marvell Header Mode
       o L2 IGMP support
    o Rx descripors: q0=128
    o Tx descripors: q0=532
    o Loading network interface(s):
       o register under mv88fx_eth platform
  sd 0:0:2:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
   sda:
  sd 0:0:2:0: [sdc] Sector size 0 reported, assuming 512.
  sd 0:0:3:0: [sdd] Write Protect is off
  sd 0:0:3:0: [sdd] Mode Sense: 23 00 00 00
       o eth0, ifindex = 2, GbE port = 0
  
  Warning: Giga 1 is Powered Off
  
  Warning: Giga 1 is Powered Off
  
  mvFpRuleDb (c8d38000): 2048 entries, 8192 bytes
  SPI Serial flash detected @ 0xf4000000, 512KB (8sec x 64KB)
  sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
  sd 0:0:1:0: [sdb] Sector size 0 reported, assuming 512.
  No NAND device found!!!
  mice: PS/2 mouse device common for all mice
  Linux telephony interface: v1.00
  md: linear personality registered for level -1
  md: raid0 personality registered for level 0
  md: raid1 personality registered for level 1
  md: raid6 personality registered for level 6
  md: raid5 personality registered for level 5
  md: raid4 personality registered for level 4
  sd 0:0:3:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
   sdc:
  sd 0:0:3:0: [sdd] Sector size 0 reported, assuming 512.
  device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
   sdb:
  TCP cubic registered
  NET: Registered protocol family 17
  NET: Registered protocol family 15
  RPC: Registered udp transport module.
  RPC: Registered tcp transport module.
  rtc mv_rtc: setting system clock to 2012-05-13 09:43:40 UTC (1336902220)
   sdd: sda1 sda2 sda3 sda4 sda5 sda6
  sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
  sd 0:0:0:0: [sda] Attached SCSI disk
   sdb1 sdb2 sdb3 sdb4 sdb5 sdb6
   sdd1 sdd2 sdd3 sdd4 sdd5 sdd6
   sdc1 sdc2 sdc3 sdc4 sdc5 sdc6
  sd 0:0:3:0: [sdd] Sector size 0 reported, assuming 512.
  sd 0:0:2:0: [sdc] Sector size 0 reported, assuming 512.
  sd 0:0:1:0: [sdb] Sector size 0 reported, assuming 512.
  sd 0:0:3:0: [sdd] Attached SCSI disk
  sd 0:0:2:0: [sdc] Attached SCSI disk
  sd 0:0:1:0: [sdb] Attached SCSI disk
  md: Waiting for all devices to be available before autodetect
  md: If you don't use raid, use raid=noautodetect
  md: Autodetecting RAID arrays.
  md: Scanned 0 and added 0 devices.
  md: autorun ...
  md: ... autorun DONE.
  RAMDISK: gzip image found at block 0
  VFS: Mounted root (ext2 filesystem) on device 1:0.
  md: md0 stopped.
  md: bind<sdb1>
  md: bind<sdc1>
  md: bind<sdd1>
  md: bind<sda1>
  raid1: raid set md0 active with 4 out of 4 mirrors
  md0: detected capacity change from 0 to 1024393216
   md0: unknown partition table
  kjournald starting.  Commit interval 5 seconds
  EXT3 FS on md0, internal journal
  EXT3-fs: mounted filesystem with writeback data mode.
  md: md10 stopped.
  md: bind<sdb5>
  md: bind<sdc5>
  md: bind<sdd5>
  md: bind<sda5>
  raid1: raid set md10 active with 4 out of 4 mirrors
  md10: detected capacity change from 0 to 1024446464
  md: md1 stopped.
  md: bind<sdb2>
  md: bind<sdc2>
  md: bind<sdd2>
  md: bind<sda2>
  raid1: raid set md1 active with 4 out of 4 mirrors
  md1: detected capacity change from 0 to 5119135744
   md1: unknown partition table
  kjournald starting.  Commit interval 5 seconds
  EXT3 FS on md1, internal journal
  EXT3-fs: recovery complete.
  EXT3-fs: mounted filesystem with writeback data mode.
  kjournald starting.  Commit interval 5 seconds
  EXT3 FS on md1, internal journal
  EXT3-fs: mounted filesystem with writeback data mode.
  VFS: Mounted root (ext3 filesystem) on device 9:1.
  Trying to move old root to /initrd ... okay
  Freeing init memory: 152K
  EXT3-fs: Unrecognized mount option "relatime" or missing value
   md10: unknown partition table
  Adding 1000428k swap on /dev/md10.  Priority:-1 extents:1 across:1000428k 
  kjournald starting.  Commit interval 5 seconds
  EXT3 FS on md0, internal journal
  EXT3-fs: mounted filesystem with writeback data mode.
  usbcore: registered new interface driver usbfs
  usbcore: registered new interface driver hub
  usbcore: registered new device driver usb
  ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
  ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
  ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
  ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
  usb usb1: configuration #1 chosen from 1 choice
  hub 1-0:1.0: USB hub found
  hub 1-0:1.0: 1 port detected
  ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  uhci_hcd: USB Universal Host Controller Interface driver
  Initializing USB Mass Storage driver...
  usbcore: registered new interface driver usb-storage
  USB Mass Storage support registered.
  usbcore: registered new interface driver usblp
  usb 1-1: new high speed USB device using ehci_marvell and address 2
  usb 1-1: configuration #1 chosen from 1 choice
  hub 1-1:1.0: USB hub found
  hub 1-1:1.0: 2 ports detected
  usb 1-1.2: new full speed USB device using ehci_marvell and address 3
  usb 1-1.2: configuration #1 chosen from 1 choice
  usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04A9 pid 0x1094
  eth0: link down
  eth0: started
  eth0: link up, full duplex, speed 1 Gbps
  GbE port 0: TxEnable WA - Enabled, deep=2, tx_en_bk=1
  
  GbE port 0: TxEnable WA - Enabled, deep=2, tx_en_bk=1
  
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
  md: md21 stopped.
  md: bind<sda6>
  raid1: raid set md21 active with 1 out of 2 mirrors
  md21: detected capacity change from 0 to 484830994432
   md21: unknown partition table
  md: md23 stopped.
  md: bind<sdc6>
  raid1: raid set md23 active with 1 out of 2 mirrors
  md23: detected capacity change from 0 to 484830994432
   md23: unknown partition table
  md: md22 stopped.
  md: bind<sdb6>
  raid1: raid set md22 active with 1 out of 2 mirrors
  md22: detected capacity change from 0 to 484830994432
   md22: unknown partition table
  md: md24 stopped.
  md: bind<sdd6>
  raid1: raid set md24 active with 1 out of 2 mirrors
  md24: detected capacity change from 0 to 484830994432
   md24: unknown partition table
  XFS mounting filesystem md21
  Ending clean XFS mount for filesystem: md21
  XFS mounting filesystem md22
  Ending clean XFS mount for filesystem: md22
  XFS mounting filesystem md23
  Ending clean XFS mount for filesystem: md23
  XFS mounting filesystem md24
  Ending clean XFS mount for filesystem: md24
  warning: `proftpd' uses 32-bit capabilities (legacy support in use)
  bfSetMagicKey > Changed to 0x71 from 0x5c
  root@Nas:~#

Pages in category "LS-QVL"

The following 4 pages are in this category, out of 4 total.