Difference between revisions of "Convert your MIPSel LinkStation into a full-blown Debian system"

From NAS-Central Buffalo - The Linkstation Wiki
Jump to: navigation, search
 
Line 1: Line 1:
(:note Temporary Tutorial | The information here will change a lot in the future but wanted to get the information out here.:)
+
Temporary Tutorial | The information here will change a lot in the future but wanted to get the information out here.
 +
 
 +
 
 +
== Files ==
  
!! Files
 
 
You can get the required files here http://www.geishuettner.de/docs/Linkstation/ and find more information in the [[http://linkstationwiki.org/forum/index.php?action=vthread&forum=3&topic=23 | forum]] unil a nicer article finds it way here.
 
You can get the required files here http://www.geishuettner.de/docs/Linkstation/ and find more information in the [[http://linkstationwiki.org/forum/index.php?action=vthread&forum=3&topic=23 | forum]] unil a nicer article finds it way here.
  
!! Overview
+
 
 +
== Overview ==
 +
 
 
You don't have to open the linkstation in order to install Debian on it. You just need telnet access to your linkstation.
 
You don't have to open the linkstation in order to install Debian on it. You just need telnet access to your linkstation.
  
Line 12: Line 16:
 
# After the installer is finished you have to swap your partitions using the included ''swappart'' program
 
# After the installer is finished you have to swap your partitions using the included ''swappart'' program
  
This is just a quick overview for detailed instructions have a look at the [[http://www.geishuettner.de/docs/Linkstation/Hacking%20Linkstation%20II.pdf | hacking howto (PDF)]] at the page linked above.
+
This is just a quick overview for detailed instructions have a look at the [[http://www.geishuettner.de/docs/Linkstation/Hacking%20Linkstation%20II.pdf hacking howto (PDF)]] at the page linked above.
  
!!! Notes
+
=== Notes ===
 
The installer script will take your previous network configuration to the debian installation. My installation didn't boot when DHCP was enabled, so to be on the save side use a static IP address.
 
The installer script will take your previous network configuration to the debian installation. My installation didn't boot when DHCP was enabled, so to be on the save side use a static IP address.
  
 
You can always revert back to the stock firmware by running the ''swappart'' program again. In case something goes terribly wrong this can also be done from a PC when you connect the hard disk directly.
 
You can always revert back to the stock firmware by running the ''swappart'' program again. In case something goes terribly wrong this can also be done from a PC when you connect the hard disk directly.

Revision as of 23:47, 14 June 2006

Temporary Tutorial | The information here will change a lot in the future but wanted to get the information out here.


Files

You can get the required files here http://www.geishuettner.de/docs/Linkstation/ and find more information in the [| forum] unil a nicer article finds it way here.


Overview

You don't have to open the linkstation in order to install Debian on it. You just need telnet access to your linkstation.

  1. Download the debil installer
  2. unpack it
  3. run the debil.sh script this will take you to the debian installer after downloading it
  4. After the installer is finished you have to swap your partitions using the included swappart program

This is just a quick overview for detailed instructions have a look at the [hacking howto (PDF)] at the page linked above.

Notes

The installer script will take your previous network configuration to the debian installation. My installation didn't boot when DHCP was enabled, so to be on the save side use a static IP address.

You can always revert back to the stock firmware by running the swappart program again. In case something goes terribly wrong this can also be done from a PC when you connect the hard disk directly.