From NAS-Central Buffalo - The Linkstation Wiki

Revision as of 00:16, 17 December 2006 (view source) Ramuk (Talk | contribs) m ← Older edit		Revision as of 12:56, 17 December 2006 (view source) WizardFusion (Talk | contribs) m (→Option1: crossover cable) Newer edit →
Line 10:		Line 10:
	Your friend has a network card. Yay !		Your friend has a network card. Yay !
	Just connect using a crossover cable		Just connect using a crossover cable
		+
		+	The image below shows the pin-layouts for the standard network crossover cables.
		+
		+	[[CrossOverCableLayout.gif]]
	<add crossover how-to here>		<add crossover how-to here>

---

Revision as of 12:56, 17 December 2006

Contents 1 Direct PC Connection 1.1 USB bridge cable 1.2 Ethernet to Ethernet 1.2.1 Option1: crossover cable 1.2.2 Option2: crossover cable and usb network card 1.2.3 Option3: same as above but can't find a crossover cable 1.2.4 Likely required: Static IP setup on the Linkstation 1.2.5 Likely required: Static IP setup on the PC

Direct PC Connection

So you go to a friend's place and you'd like to share some files. How ?

USB bridge cable

Unknown. they seem to require both ends to use the same software, and generally runs on Windows-only machines. TBD.

Ethernet to Ethernet

Option1: crossover cable

Your friend has a network card. Yay ! Just connect using a crossover cable

The image below shows the pin-layouts for the standard network crossover cables.

CrossOverCableLayout.gif

<add crossover how-to here>

Option2: crossover cable and usb network card

Your friend does not have a network card, but has usb ports. No problem ! Buy a usb network adapter and connect on his/her PC. An example is the Linksys USB200M 10/100 USB2.0 network adapter, fairly inexpensive.

Option3: same as above but can't find a crossover cable

You can't find a crossover cable? no problem. Use normal cables, but use a Ethernet hub or Ethernet switch or even a router to connect the PC and the Linkstation together.

Likely required: Static IP setup on the Linkstation

as per lb_worm's suggestion, on your Linkstation, change those 2 files:

1) set the /etc/network/interfaces to:

1. Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or
2. /usr/share/doc/ifupdown/examples for more information.

auto lo iface lo inet loopback

auto eth0 iface eth0 inet static address 192.168.11.160 netmask 255.255.255.0 geteway 192.168.11.1 network 192.168.11.0

auto eth0:auto iface eth0:auto inet dhcp

2) Edit the dhcp config file /etc/dhcpc/config to:

1. Config file for dhcpcd.

case ${INTERFACE} in eth0)

1. Uncomment this to allow dhcpcd to set the DNS servers in /etc/resolv.conf
2. If you are using resolvconf then you can leave this commented out.

SET_DNS='yes'

1. Uncomment this to allow dhcpcd to set the NIS domainname of the host to the
2. domainname option supplied by DHCP server.
3. SET_DOMAIN='yes'

1. Uncomment this to allow dhcpcd to set hostname of the host to the
2. hostname option supplied by DHCP server.
3. SET_HOSTNAME='yes'

1. Uncomment this to allow dhcpcd to set the NTP servers in /etc/ntp.conf
2. SET_NTP='yes'

1. Uncomment this to allow dhcpcd to set the YP servers in /etc/yp.conf
2. SET_YP='yes'

1. Add other options here, see man 8 dhcpcd-bin for details.

OPTIONS='-d -t 30 interface eth0:auto'

1. Add other interfaces here

• )

esac

The -d option will generate some debug.

Likely required: Static IP setup on the PC

Windows XP: Start->Control Panel->Network Connections. Right click on your network adapter(likely called "Local Area Connection" ->Properties

Select "Internet Protocol (TCP/IP)

This article is currently a stub. You can help this Wiki by expanding it . This template will categorize articles that include it into Category:Stubs.