Frequently Asked Questions
- 1 How do I install the hard drive in my kuro and fully assemble my kuro?
- 2 Help, I can't ping or login to my new Kuro Box. The power light is on. The link light is on. The other lights are off.
- 3 My box is not responding and the DIAG led is blinking. What does that mean?
- 4 Exactly what does the red button on the back do? Will it force EM mode?
- 5 What is EM mode?
- 6 OK, how do I force EM mode?
- 7 The kernel loaded from flash is old. Is there some way I can run with a newer kernel?
- 8 I see that the kurobox has flash memory. Can I modify the flash contents?
- 9 My question isn't answered here. Where else can I look for an answer?
How do I install the hard drive in my kuro and fully assemble my kuro?
Read the instructions that came with your Kuro. They are also available here
1. The fallback IP address for the Kuro Box is 192.168.11.150. If your computer is not on the same subnet (first three numbers don't match) you will not be able to communicate with your Kuro Box. If only the first 2 numbers match change the subnet mask on your computer to 255.255.0.0. If only the first number matches change the subnet mask to 255.0.0.0. Be sure to change your subnet mask back to its original setting after you have setup your Kuro Box.
2. Another option is to add a static route to the 192.168.11.0 subnet. You might want to do this especially if you are going to leave the kurobox at 192.168.11.150 for an extended period of time. If your computer is running windows bring up a command shell (c: prompt) to use the route command. You need to know your computer's IP address and the interface number. You can figure these out with "ipconfig" and "route print". A command like this is what you need:
C:\> route ADD 192.168.11.0 MASK 255.255.255.0 192.168.1.100 METRIC 1 IF 1 destination^ ^mask ^gateway metric^ ^ (your IP address) Interface^
Use your computer's IP address for the gateway. Use the interface number for that IP address as the IF parameter.
If your computer is running linux or another unix, use a command like this to add a static route (this command needs to be run as root):
# route add -net 192.168.11.0 netmask 255.255.255.0 eth0
Your interface may not be eth0. Use the ifconfig command to determine the correct interface.
3. If all else fails, connect the Kuro Box directly to your computer. Change the IP address of your computer to 192.168.11.149 and change your subnet mask to 255.255.255.0. You should now be able to telnet directly into your Kuro Box at 192.168.11.150 and install your system.
The LEDs and their meanings are described on the Hardware LEDs page.
The red button's primary function is to disable the watchdog timer. This is useful for kernel development and when using a JTAG cable to repair the flash contents. To disable the watchdog timer press the red button when you power up the Kuro. The Kuro will flash red and green lights if the watchdog timer is disabled.
Its function depends on whether or not you are using U-Boot. If you are using U-Boot, it will either disable the watchdog timer or force EM mode depending when it is pressed. To force EM mode Just start the Kuro and when the power light stops blinking press the red button. Your Kuro will boot in EM mode.
If you are not using U-Boot, and unless you installed U-Boot you are not using it, the red button will not force EM mode unless its function has been changed by a booted operating system. This means that if your Kuro hangs during boot and you are not using U-Boot, the red button cannot be used to force EM mode.
What is EM mode?
EM , or Emergency mode, is the initrd and kernel stored in the firming.bin portion of flash from which resides at ffc00000 to ffefffff. It is a stripped down operating system that is useful for both installing an operating system on you kurobox or recovering your kurobox.
OK, how do I force EM mode?
If you cannot get to an SSH prompt to force EM mode you have two options.
- The first is to remove the hard disk and replace it with a blank drive and restart it. the Kuro will boot to EM mode. once there you can execute the command echo -n "NGNG" > /dev/fl3 and then shutdown your Kuro and replace the drive with the original drive.
- The other option is to just install a blank drive in your kuro.
The kernel loaded from flash is old. Is there some way I can run with a newer kernel?
You have two options for running a newer kernel
I see that the kurobox has flash memory. Can I modify the flash contents?
Are you sure you know what you are doing? The flash should not be toyed with willy-nilly. Read up on it's purpose on the Flash ROM page.