Information/HGAVR
From NAS-Central Buffalo - The Linkstation Wiki
This article was originally based on work by Frontalot at linkstationwiki.org and has since been expanded.
Contents |
The Linkstation HG AVR
Hardware Information
Basic Information
The AVR in the HG Linkstation is an AT90S2313-4SC made by ATMEL, not Freescale as previously documented here. This is a cheap 4 MHz AVR with 2k program space and 128 EEPROM.
CN4 (next to the battery on the LS HG board) is a 6 pin ISP header that can be used to read/program the AVR with a cheap device such as a usbtiny that can be purchased as a kit/assembled from various hobby electronics websites. The cable supplied with the usbtiny has the same pin out and fits perfectly.
Pin assignment for the HGAVR
The pin assignment and its functions used in HG is listed in the following table:
NOTE THIS SECTION IS WRONG. THE AVR IN THE HG IS 20 PIN. HAVE A LOOK.
| PIN | SIGNAL | Description | PIN | SIGNAL | Description |
| 1 | ZIRQ | CN3.3 | 28 | ZRST | CN3.4 |
| 2 | PTA0 | DIAG LED | 27 | PTA5 | Power switch input |
| 3 | VSS | CN3.6 / CN3.9 | 26 | PTD4 | Fan pulse input for status checking |
| 4 | OSC1 | CN3.1 | 25 | PTD5 | HRST (CN5.13) |
| 5 | OSC2 | - | 24 | PTD2 | Control 12V feed to the main switching power via TR5, TR3 |
| 6 | PTA1 | Disk full LED | 23 | PTA4 | Reset switch input |
| 7 | VDD | CN3.2 | 22 | PTD3 | Fan speed control via TR2,TR1 |
| 8 | PTA2 | Power LED green | 21 | PTB0 | CN3.5 |
| 9 | PTA3 | Power LED yellow | 20 | PTB1 | CN3.10 |
| 10 | PTB7 | NC | 19 | PTD1 | IDE reset / TRST (CN5.4 via R66) |
| 11 | PTB6 | NC | 18 | PTB2 | CN3.7 |
| 12 | PTB5 | NC | 17 | PTB3 | CN3.8 |
| 13 | RXD | Connects to /dev/ttyS1 | 16 | PTD0 | Flash reset (ZRP on IC8.12) |
| 14 | TXD | Connects to /dev/ttyS1 | 15 | PTB4 | NC |
Software Information
Interaction With AVR In Linux
The AVR controls much of the LinkStation hardware, including the power button and LED indicator. It is controlled by the commands sent to /dev/ttyS1. To send commands to the AVR:
echo -n "commands" > /dev/ttyS1
| Command | Action/Code |
| \30\30\30\30 | Stops smbd and atalkd if /dev/hda3 is not mounted to /mnt. Sent by /www/script/melsub_diskcheck.sh. |
| [[[[ | Starts slowly blinking power LED (sleep). |
| ]]]] | High-speed cooling fan rotation. |
| \\\\ | Low-speed cooling fan rotation. |
| >>>> | Unknown. Sent by ppc_uartd on boot. |
| AAAA | Unknown. Sent by ppc_uartd on boot. |
| CCCC | Sent by shutdown -r now (reboot). |
| EEEE | Sent by shutdown -h now (halt). |
| FFFF | Unknown. Sent by ppc_uartd on boot. |
| JJJJ | Unknown. Sent by ppc_uartd on boot. |
| KKKK | Unknown. Sent by ppc_uartd on boot. |
| QQQQ | Unknown. Sent by ppc_uartd on set timer. |
| RRRR | End of clear flash memory. |
| SSSS | Start of clear flash memory and /www/script/melsub_init.sh. Sent by /www/script/melsub_flash.sh. |
| TTTT | Flash memory update completed (stops blinking power, disk full, and diagnostic LEDs). |
| UUUU | Flash memory update started (starts blinking power, disk full, and diagnostic LEDs). |
| VVVV | Turns off disk full LED. |
| WWWW | Turns on disk full LED. |
| XXXX | Stops blinking disk full LED. |
| YYYY | Starts blinking disk full LED. |
| ZZZZ | Stops slowly blinking power LED. Sent by ppc_uartd. |
| gggg | Diagnostic LED blinks 3 times and system shutdown (partition error). |
| iiii | Diagnostic LED blinks 4 times and system shutdown (cooling fan error). |
| kkkk | Diagnostic LED blinks 5 times and system powers off (flash memory error). |
| mmmm | Diagnostic LED blinks 6 times and system shutdown (hard drive or ppc_uartd error). |
| oooo | Diagnostic LED blinks 7 times and system shutdown (RAM, NIC, or HDD controller error). |
