Difference between revisions of "Information/LSProLED"

From NAS-Central Buffalo - The Linkstation Wiki
Jump to: navigation, search
(Link/Activity LED)
(verified link colors, removed debate postit)
Line 14: Line 14:
 
|}
 
|}
  
==== Link/Activity LED ====
+
==== Link/Activity LED ==== (There is no difference in color)
 
{| style="background:#DDDDDD; color:black" WIDTH=50%
 
{| style="background:#DDDDDD; color:black" WIDTH=50%
 
|-  
 
|-  
|WIDTH=30% style="background:#666666; color:orange"|solid orange
+
|WIDTH=30% style="background:#666666; color:green"|solid green
 
|10Mbps connection.
 
|10Mbps connection.
 
|-
 
|-
Line 23: Line 23:
 
|100Mbps connection.
 
|100Mbps connection.
 
|-
 
|-
|style="background:#BBBBBB; color:blue"|solid blue
+
|style="background:#BBBBBB; color:green"|solid green
 
|1000Mbps / 1Gbps connection.
 
|1000Mbps / 1Gbps connection.
 
|}
 
|}
  
{{Postit |Debate | There is some debate with regards to the color of these lights at various connection speeds (1000/100/10 MBPS) these ARE for sure the color of the LED light on the HG models, if someone can confirm that the colors are the same on the PRO that of course would be helpful}}
 
  
 
==== Orange INFO LED ====
 
==== Orange INFO LED ====

Revision as of 05:23, 27 April 2007

Link.png This article is currently a stub. You can help this Wiki by expanding it

. This template will categorize articles that include it into Category:Stubs.

Lspro-front.jpg


Power LED

solid green System on (normal).
blinks green System booting or flash memory write in progress.

==== Link/Activity LED ==== (There is no difference in color)

solid green 10Mbps connection.
solid green 100Mbps connection.
solid green 1000Mbps / 1Gbps connection.


Orange INFO LED

The way the unit gives diagnostic codes is by long and short flashes of the specific light. The number of long flashes give the first of two numbers and the number of short flashes give the second. For instance, one long flash and three short flashes would indicate an error of 13 -

I 10 PCB overheat
I 20 internal HDD formatting
I 21 internal HDD checking (fscking?)
I 22 internal HDD recovering (not sure about this one...)
I 23 System initialising
I 25 firmware updating
I 26 initialising web setting
I 27 USB disk checking
I 28 USB disk formatting

Red ERROR LED

The way the unit gives diagnostic codes is by long and short flashes of the specific light. The number of long flashes give the first of two numbers and the number of short flashes give the second. For instance, one long flash and three short flashes would indicate an error of 13 -

E 00 (No light, beep only) - MPU error
E 01 DRAM data line error
E 02 DRAM address line error
E 03 RTC chip error
E 04 Flash rom error
E 10 UPS power loss
E 11 fan error (RPM too low or not functional)
E 12 cooling error (unable to remove heat by the fan)
E 15 disk error
E 16 unable to locate internal HDD
E 17 Unable to communicate with the RTC chip
E 21 unable to communicate with the Phy chip
E 22 mount error.

The original Buffalo firmware has the following error messages based on the number of flashes:

3 Partition problem with hard drive. Reformat the hard drive.
4 Fan problem.
5 ROM problem.
6 Hard Drive can not be recognized.
7 Problem with motherboard (RAM, LAN, or Hard Drive controller).