Difference between revisions of "Information/MIPSelOverview"

From NAS-Central Buffalo - The Linkstation Wiki
Jump to: navigation, search
Line 61: Line 61:
*LS120: Samsung SP1203N
*LS120: Samsung SP1203N
*LS160: Western Digital WD1600
*LS160: Western Digital WD1600
*LS250: Samsung SP2514N
*LS250: Samsung SP2514N or WDC WD2500BB-22GUC0
*LS300: ?
*LS300: ?
== Power Supply ==
== Power Supply ==

Revision as of 07:07, 26 August 2006

This article Based on work by Patrick Arnoux.,Johannes Kaiser, nix, noName, frontalot, non, marge, and admin.Originally by admin. at Linkstationwiki.org


CPU 400MHz IDT 79RC32434-400BC with MIPSel CPU core
Flash ROM 4MB Macronix MX29LV320T.
USB 2 type A(rear - /dev/usb/lp0, front - /dev/usb/lp1) - NEC D720101GJ
NIC 10/100Mb Realtek 8201CPPCI ethernet controller
IDE Controller IT8211 PCI IDE disk controller.
Stock Firmware 2.x

Main Board

Serial Console: Adding a serial interface is difficult as the only serial port is connected to the AVR microcontroller. Several Japanese LinkStation owners have succeeded used the one serial port for other purposes. Please help out by translating the Japanese BBS page or providing schematics.

The following hardware can be found on the main board:

  • IDT 79RC32434-400BC Integrated Communications Processor, containing
    • 32-bit @ 400MHz MIPSel CPU core (el -> le -> little endian) with MIPS32 instructions set architecture. Based on the MIPS 4Kc core.
    • 10/100Mb Ethernet channel {:MII:Media Independent Interface}/{:RMII:Reduced Media Independent Interface} interface controller
    • Serial UART, 16550 compatible
    • DDR memory controller, can handle up to 256MB
    • general purpose memory controller
    • PCI controller
    • DMA controller
    • I'^2^'C bus
    • general purpose I/O connectors
    • JTAG interface (hardware-supported debugging)
    • Watchdog timer
    • No FPU (floating point is done via software emulation)
  • 8201CP 'PHYceiver' - Physical Ethernet tranceiver, connected to the ICP's Ethernet channel
  • RAM - 64MB Micron MT 46V32MI6-SBC SDRAM
  • Flash ROM - 4MB Macronix MX29LV320T.
  • IT8211 PCI IDE disk controller. The stock kernel driver reports an IT8212 (an IDE RAID 0/1/0+1 controller). However, there is indeed only a IT8211 on the board.
  • USB - 2 type A connectors (rear - /dev/usb/lp0, front - /dev/usb/lp1) - NEC D720101GJ. The NEC chip supports five USB interfaces, of which only two are connected to the two plugs. Experienced tinkerer can try to add more USB plugs, according to this here.


IDE 3.5" Disk

  • LS120: Samsung SP1203N
  • LS160: Western Digital WD1600
  • LS250: Samsung SP2514N or WDC WD2500BB-22GUC0
  • LS300: ?

Power Supply

  • 25W Co., Ltd. "open frame" dual voltage power supply, from the UOP25D/325D series ([1], [2]). The power supply is actually a "brick" power supply without the usual plastic case. The UOP25D/325D series comes in different variations. The differences are the input voltage ranges, and the maximum output current and output voltage stability. 5V ±5%, 0.1A - 2A and 12V ±6%, 0.1A - 1.5A are typical output values.


  • Stock Firmware - 2.x series
  • OpenLink available