Information/MIPSelOverview
From NAS-Central Buffalo - The Linkstation Wiki
This article Based on work by Patrick Arnoux.,Johannes Kaiser, nix, noName, frontalot, non, marge, admin and kuroguy. Originally by admin. at Linkstationwiki.org
HDHLAN MIPSel (LS2)
HDHLAN MIPSel (LS2) CPU 400MHz IDT 79RC32434-400BC with MIPSel 4Kc CPU core RAM 64MB Micron MT 46V32MI6-SBC SDRAM Flash ROM 4MB Macronix MX29LV320T. USB Two type-A connectors (rear - /dev/usb/lp0, front - /dev/usb/lp1) - NEC D720101GJ NIC 10/100Mb Realtek 8201CPPCI ethernet controller IDE Controller IT8211 PCI IDE disk controller. Stock Firmware 2.x Microcontroller MC68HC908JL8 Microcontroller Analysis mipsel-hdhlan Microcontroller Analysis and Kuroguy's analysis of the pin functions Benchmarks mipsel-hdhlan Benchmarks Bootloader mipsel-hdhlan Boot Loader Overview Flash ROM mipsel-hdhlan Flash ROM Analysis Hardware mipsel-hdhlan Overview Kernel mipsel-hdhlan Kernel LED mipsel-hdhlan LED Analysis Software mipsel-hdhlan Filesystem contents Watchdog Timer mipsel-hdhlan Watchdog Timer Overview
Main Board

Serial Console: Adding a serial interface is difficult as the only serial port is connected to the housekeeping microcontroller. See Add a Serial port to the MIPS Linkstation for details.
The following hardware can be found on the main board:
- IDT 79RC32434-400BC Integrated Communications Processor, containing
- 32-bit @ 400MHz MIPSel CPU core (el -> le -> little endian) with MIPS32 instructions set architecture. Based on the MIPS 4Kc core.
- 10/100Mb Ethernet channel {:MII:Media Independent Interface}/{:RMII:Reduced Media Independent Interface} interface controller
- Serial UART, 16550 compatible
- DDR memory controller, can handle up to 256MB
- general purpose memory controller
- PCI controller
- DMA controller
- I'^2^'C bus
- general purpose I/O connectors
- JTAG interface (hardware-supported debugging)
- Watchdog timer
- No FPU (floating point is done via software emulation)
- 8201CP 'PHYceiver' - Physical Ethernet tranceiver, connected to the ICP's Ethernet channel
- RAM - 64MB Micron MT 46V32MI6-SBC SDRAM
- Flash ROM - 4MB Macronix MX29LV320T.
- IT8211 PCI IDE disk controller. The stock kernel driver reports an IT8212 (an IDE RAID 0/1/0+1 controller). However, there is indeed only a IT8211 on the board.
- USB - 2 type A connectors (rear - /dev/usb/lp0, front - /dev/usb/lp1) - NEC D720101GJ. The NEC chip supports five USB interfaces, of which only two are connected to the two plugs. Experienced tinkerer can try to add more USB plugs, according to this here.
Periphery
IDE 3.5" Disk
- LS120: Samsung SP1203N / Western Digital WDC WD1200BB-00GUC0
- LS160: Western Digital WD1600
- LS250: Samsung SP2514N or V120CE(HA250JC) / Western Digital WD2500BB-22GUC0
- LS300: Western Digital WD3200JB-00KFA0
Power Supply
- 25W Univive Co., Ltd. "open frame" dual voltage power supply, from the UOP25D/325D series ([1], [2]). The power supply is actually a "brick" power supply without the usual plastic case. The UOP25D/325D series comes in different variations. The differences are the input voltage ranges, and the maximum output current and output voltage stability. 5V ±5%, 0.1A - 2A and 12V ±6%, 0.1A - 1.5A are typical output values.
Software
- Stock Firmware - 2.x series
- OpenLink available