Difference between revisions of "Install Gentoo Linux"

From NAS-Central Buffalo - The Linkstation Wiki
Jump to: navigation, search
(Finished clean up and added top level sections.)
m
Line 80: Line 80:
 
  # mount -t ext3 /dev/hda1 /gentoo  
 
  # mount -t ext3 /dev/hda1 /gentoo  
  
== Install Gentoo KuroBox Base 3 ==
+
== Install Gentoo KuroBox Stage 3 ==
 
We now use our FTP client to upload system-20060108.tar.gz from http://www.kurobox.com/downloads/gentoo to the /gentoo directory on the kuro. we also upload portage-snapshot-20060108.tar.gz. Use the most current one you can find. It can be found at any of the gentoo mirrors. The last file we need to upload is the current portage overlay which was portage-overlay-20060122.tar.gz when I wrote this. It can also be found at http://www.kurobox.com/downloads/gentoo.  
 
We now use our FTP client to upload system-20060108.tar.gz from http://www.kurobox.com/downloads/gentoo to the /gentoo directory on the kuro. we also upload portage-snapshot-20060108.tar.gz. Use the most current one you can find. It can be found at any of the gentoo mirrors. The last file we need to upload is the current portage overlay which was portage-overlay-20060122.tar.gz when I wrote this. It can also be found at http://www.kurobox.com/downloads/gentoo.  
  

Revision as of 00:40, 14 March 2006

I'm sure I left something out, but the steps are here. A good amount of this stuff is from TGL's gentoo beta 1 how-to. As usual, backup your data before starting. You will be formatting partitions which destroys all data. You have been warned.

Contents

Preparing for Install

Start by using any FTP client to upload EM_mode_binaries.tar.bz2 (you can download it from http://kurobox.com/downloads/gentoo to /tmp on the Kuro (hint: Windows may change the extension of the file when you download it from the internet). Then login to the kuro using a telnet client

Kroutoshikou KURO-BOX (IETSUNA) 
kernel 2.4.17-kuro-box on ppc 
KURO-BOX-EM login: root 
Password:kuro

Lets see what we've got

# df
Filesystem 1k-blocks Used Available Use% Mounted on
/dev/ram0 9677 5102 4575 53% / 
#cd /tmp 
#ls 
EM_mode_binaries.tar.gz 

Change to the root and untar the binaries.

#cd / 
#tar xvzf /tmp/EM_mode_binaries.tar.gz 
bin/ 
bin/sfdisk bin/fdisk bin/bzip2 bin/date bin/chroot #

Check and set the date.

#date 
Fri Feb 1 12:37:03 JST 2006 
#date 02032238 
Thu Feb 3 22:38:00 JST 2006

We run fdisk and create partitions. I use 4 partitions. hda1 for /, hda2 for the swap space, hda3 for /var, and hda4 for my data store (/datafiles). This page from the Gentoo Handbook explains how to prepare your harddisk (create partitions). For most 10 gig for / on hda1 and /var on hda3 is adequate. 512 meg is good for a swap space on hda2 and use the remainder for /datafiles on hda4. However you decide to break up your harddisk, remember you need to mount all of the drives (except the swap and /datafiles) before you untar the system file (More on that later).

#fdisk /dev/hda 

I have read that journaling and indexing will speed up your system. If you would like to setup journaling and indexing click here, Journaling and Indexing, and follow the instructions for partitioning and formatting your drive. A tune2fs binary for the Kuro can be downloaded from http://www.kurobox.com/downloads/gentoo. When you are done come back to this page and skip down about 30 lines to the part where we create the swap space.

Once the partitions are created we format the partitions. Here we format the first partition on /dev/hda (the hard drive is /dev/hda).

# mke2fs -j /dev/hda1 
mke2fs 1.22, 22-Jun-2001 for EXT2 FS 0.5b, 95/08/09 
Filesystem label= 
OS type: Linux 
Block size=4096 (log=2) 
Fragment size=4096 (log=2) 
1251712 inodes, 2502115 blocks 
125105 blocks (5.00%) reserved for the super user 
First data block=0 
77 block groups 
32768 blocks per group, 32768 fragments per group 
16256 inodes per group 
Superblock backups stored on blocks: 
32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632 

Writing inode tables: done 
Creating journal (8192 blocks): done 
Writing superblocks and filesystem accounting information: done 

This filesystem will be automatically checked every 29 mounts or 
180 days, whichever comes first. Use tune2fs -c or -i to override.
# 

We do this for all of the partitions we plan to use.

# mke2fs -j /dev/hda3 
.
.
.
# mke2fs -j /dev/hda4 

Next we create the swap space

# mkswap /dev/hda2 
Setting up swapspace version 1, size = 518184960 bytes 
# 

We will create the directoy /gentoo and mount /dev/hda1 there. this allows us to create the gentoo system on the hard drive instead of in the flash ram disk. It will later become our root.

# mkdir /gentoo 
# mount -t ext3 /dev/hda1 /gentoo 

Install Gentoo KuroBox Stage 3

We now use our FTP client to upload system-20060108.tar.gz from http://www.kurobox.com/downloads/gentoo to the /gentoo directory on the kuro. we also upload portage-snapshot-20060108.tar.gz. Use the most current one you can find. It can be found at any of the gentoo mirrors. The last file we need to upload is the current portage overlay which was portage-overlay-20060122.tar.gz when I wrote this. It can also be found at http://www.kurobox.com/downloads/gentoo.

Now we make /gentoo/var and mount /dev/hda3 there

# mkdir /gentoo/var 
# mount -t ext3 /dev/hda3 /gentoo/var 

We now change directories to /gentoo and untar the system in what will be our root directory

#cd /gentoo
# tar xvjf system-20060108.tar.gz 
./bin/ 
./bin/gawk 
.
.
.
./var/state/.keep 
./var/empty/ 
./var/empty/.keep 
./bin/awk 
# 

Next we mount /proc

# mount -t proc none /gentoo/proc 

and configure name resolution

# cp -L /etc/resolv.conf /gentoo/etc/ 

And then we chroot into the new gentoo system

# chroot /gentoo /bin/bash 
KURO-BOX-EM / # 

We set up the terminal

KURO-BOX-EM / #export TERM=vt100

Next we setup portage. This might be a good time to get a drink or walk the dog.

KURO-BOX-EM / #cd /var 
KURO-BOX-EM var #tar xvjf /portage-20060126.tar.gz 

Next we install the portage overlay

KURO-BOX-EM var # mkdir overlays 
KURO-BOX-EM var # cd overlays 
KURO-BOX-EM overlays # mkdir 20060122 
KURO-BOX-EM overlays # cd 20060122 
KURO-BOX-EM 20060122 # tar xvjf /overlay-20060122.tar.gz 
profiles/ 
profiles/kurobox/ 
profiles/kurobox/make.defaults 
.
.
.
sys-kernel/modules-kurobox-hg/Manifest 
sys-kernel/modules-kurobox-hg/files/ 
sys-kernel/modules-kurobox-hg/files/digest-modules-kurobox-hg-2.4.17 
KURO-BOX-EM 20060122 # 

Now we create empty directories for distfiles and binaries

KURO-BOX-EM 20060122 # cd /var 
KURO-BOX-EM portage # mkdir packages 
KURO-BOX-EM portage # mkdir distfiles 

Now we configure portage

KURO-BOX-EM portage #cd /etc 
KURO-BOX-EM etc #nano make.conf 
#The GENTOO_MIRRORS and SYNC lines need to be adjusted. Pick the three nearest sites listed at http://www.gentoo.org/main/en/mirrors.xml for your GENTOO_MIRRORS line. 
CFLAGS="-O2 -mcpu=603e -fno-strict-aliasing -pipe -fsigned-char" 
CXXFLAGS="${CFLAGS}" 

PORTDIR=/var/portage 
DISTDIR=/var/distfiles 
PKGDIR=/var/packages 
RPMDIR=/var/rpm 
#I store my overlays in a directory based on the date of the overlay 
PORTDIR_OVERLAY="/var/overlays/20060122" 

RSYNC_EXCLUDEFROM=/etc/portage/rsync_excludes 

GENTOO_MIRRORS="http://www.gatech.edu/pub/gentoo/ http://ftp.ucsb.edu/pub/mirro..." 

SYNC="rsync://rsync.europe.gentoo.org/gentoo-portage" 

Next we set up the portage profile

KURO-BOX-EM etc #rm make.profile

Notice the 20060122 in the following line. Change it to the date of your overlay in order to point to the correct directory. The link is the relative diretory from /etc. Notice we have to go up 1 level (../) before going back down the /var part of the tree.

KURO-BOX-EM etc #ln -s ../var/overlays/20060122/profiles/kurobox make.profile 
KURO-BOX-EM kurobox #cd /var/overlays 

Notice the 20060122 in the following lines. Change it to the date of your overlay in order to point to the correct directory. It is the relative path from the profile in the overlay to the profile in the official portage tree. Each ../ indicates a directory up in the tree. Just count the directories up and then add the path back down.

KURO-BOX-EM overlays # echo "../../../../portage/profiles/default-linux/ppc/2005.1/ppc" > 20060122/profiles/kurobox/parent 
KURO-BOX-EM overlays #cd /etc 

Now lets regenerate the portage cache. This would be a good time for a bathroom break or a quick run to the store for a snack.

KURO-BOX-EM etc #emerge metadata 
Updating Portage cache: 100% 
KURO-BOX-EM etc # 

We edit /etc/fstab as required. Here are the important parts of my fstab:

# NOTE: If your BOOT partition is ReiserFS, add the notail option to opts. 
/dev/hda1     /           ext3     noatime      0      0 
/dev/hda2     none        swap     sw           0      1 
/dev/hda3     /var        ext3     noatime      0      2 
/dev/hda4     /datafiles  ext3     noatime      0      0 

# NOTE: The next line is critical for boot! </span>
none /proc proc defaults 0 0

Now we'll check if the system is up to date

KURO-BOX-EM etc #emerge -puD system 

If there are packages that need installing/upgrading wait until you finish the install guide and reboot the system before running emerge -uD world. I know for a fact that glibc won't emerge if you try to do it right now, but it will after the install is complete.

Configure New System

Next we change the root password and add a user who is a member of wheel so they can su to root.

KURO-BOX-EM etc #passwd 
New UNIX password: 
Retype new UNIX password: 
passwd: password updated successfully 
KURO-BOX-EM etc # useradd dtaylor -m -G users,wheel -s /bin/bash 
KURO-BOX-EM etc # passwd dtaylor 
New UNIX password: 
Retype new UNIX password: 
passwd: password updated successfully 
KURO-BOX-EM etc # 

Next we configure the network.

KURO-BOX-EM etc #cd conf.d 
KURO-BOX-EM conf.d #cp net.example net 
KURO-BOX-EM conf.d #nano net 

If you want a static IP address you need to uncomment a couple of lines. Scroll down to the section INTERFACE HANDLERS and uncomment the following lines. In the example I have set the IP address to 192.168.0.9, the network mask to 255.255.255.0, and the gateway to 192.168.0.1. Do not uncomment the default via 4321:0:1:2:3:4:567:89ab". You will want to change the IP address gateway address to suit your network. If you want to use DCHP, don't edit the file at all as it defaults to DCHP.

config_eth=( 192.168.0.9 netmask 255.255.255.0
broadcast 192.168.0.255 ) 

routes_eth0=( 
"default via 192.168.0.1" 
# "default via 4321:0:1:2:3:4:567:89ab" 
)


Add net.eth0 to your default runlevel or you won't be able to log in.

KURO-BOX-EM conf.d #cd /etc 
KURO-BOX-EM etc #rc-update add net.eth0 default 

Now we get SSH working. This step will take a few minutes and will throw a few errors.

KURO-BOX-EM etc #/etc/init.d/sshd start 

Then we start putty on our computer and try to login. Once you are sure you can login exit putty, stop sshd, and add it to the default runlevel.

KURO-BOX-EM etc #/etc/init.d/sshd stop 
KURO-BOX-EM etc #rc-update add sshd dafault 

Next we make sure that the proper daemons are set to the default runlevel

KURO-BOX-EM etc # ls runlevels/default/ 
local net.eth0 netmount sshd 

Clean up and Reboot

and then we exit the chroot system

KURO-BOX-EM etc # exit 
# 

Unmount everything

# cd / 
# umount /gentoo/var 
# umount /gentoo/proc 
# umount /gentoo 

Set the box to boot to the new system

# echo -n "OKOK" > /dev/fl3 

and then restart the system

# shutdown -r now 

Wait a few minutes and then log onto your kuro with putty. Now would be a good time to update everything and take a short vacation as it will be emerging applications for a day or three.

KURO-BOX-EM # cd / 
KURO-BOX-EM # emerge -uD world 

Last we need to update our config files. Don't do this blindly as you can easily break your brand new system. You need to understand what the configuration files mean and choose what lines you want to edit.

KURO-BOX-EM # etc-update