Difference between revisions of "Install a JTAG Port"

From NAS-Central Buffalo - The Linkstation Wiki
Jump to: navigation, search
m
 
(2 intermediate revisions by one user not shown)
Line 10: Line 10:
 
|Connector || - || CN5 (LS1/HG/Kuro)<br>CN11 (TS) || CN3 || -
 
|Connector || - || CN5 (LS1/HG/Kuro)<br>CN11 (TS) || CN3 || -
 
|-
 
|-
| nTRST || 1 || - || 2 || 1  
+
| nTRST || 1 || 4 (not normally needed) || 2 || 1  
 
|-
 
|-
 
| TDI || 3 || 3 || 4 || -
 
| TDI || 3 || 3 || 4 || -
Line 36: Line 36:
 
3. for the MIPS devices (LS2), Series resistor R181 and decoupling capacitor C35 not installed. - Bridged R181, didn't install C35.
 
3. for the MIPS devices (LS2), Series resistor R181 and decoupling capacitor C35 not installed. - Bridged R181, didn't install C35.
  
4. For the PPC devices we use this pin to supple power to the buffer chip in the JTAG Cable. The series resistor must be bridged. Bridge R67 on the Kuro, Kuro HG, LS1, and LS-HG. Bridge R370 on the Terastation. This should result in a voltage of approximatley 3.3v being present on these pins.  On the LS-HS it is easiest to take the 3.3v from Pin 3 of the Serial Port connector (this is also an option on the other PPC devices).
+
4. For the PPC devices we use this pin to supple power to the buffer chip in the JTAG Cable. The series resistor must be bridged. Bridge R67 on the Kuro, Kuro HG, LS1, and LS-HG. Bridge R370 on the Terastation. This should result in a voltage of approximatley 3.3v being present on these pins.  On the LS-HS and the TS Pro v1 it is easier to take the 3.3v from Pin 3 of the 4-port header for a Serial Port connector (this is also an option on the other PPC devices).

Latest revision as of 12:36, 15 August 2009


This page will contain instructions for installing a JTAG header in all of the Linkstations and Terastations.

See Add_Jtag_Port for instructions.

Signal MIPS (LS2) Pin PPC Pin ARM (LS Pro) Pin Notes
Connector - CN5 (LS1/HG/Kuro)
CN11 (TS)
CN3 -
nTRST 1 4 (not normally needed) 2 1
TDI 3 3 4 -
TDO 5 1 7 2
TCK 9 7 8 -
TMS 7 9 6 -
Ground 2 16 3,5 -
Power 14 6 1 3, 4
sRST - - 9 -
RTCK - - 10 -

Notes: 1. For the MIPS devices (LS2), this pin must be pulled high if not controlled by the JTAG cable. Tie pin 14 to pin 1 with a 1K resistor.

2. For the MIPS devices (LS2), Series Resistor R64 not was not installed - Installed 330 ohm resistor. any value between 100 ohms and 1K will work.

3. for the MIPS devices (LS2), Series resistor R181 and decoupling capacitor C35 not installed. - Bridged R181, didn't install C35.

4. For the PPC devices we use this pin to supple power to the buffer chip in the JTAG Cable. The series resistor must be bridged. Bridge R67 on the Kuro, Kuro HG, LS1, and LS-HG. Bridge R370 on the Terastation. This should result in a voltage of approximatley 3.3v being present on these pins. On the LS-HS and the TS Pro v1 it is easier to take the 3.3v from Pin 3 of the 4-port header for a Serial Port connector (this is also an option on the other PPC devices).