KuroBoxPro

From NAS-Central Buffalo - The Linkstation Wiki
Revision as of 11:07, 29 August 2007 by Ramuk (Talk | contribs)

Jump to: navigation, search
Kuro Box Pro

Contents

Kuro Box Pro International Main Page

Hardware Specifications

Kurobox PRO
Case 60(W) x 163.6(H) x 215.5(D) mm
CPU Type Marvell 88F5182 (400MHz)
CPU Speed 400MHZ
RAM 128MB (DDR2-SDRAM)
Hard Drive Not included
IDE Host Controller Sata - Marvell
Ethernet Controller 1000BASE-T/100BASE-TX/10BASE-T (RJ-45)x1 (AUTO-MDIX)
USB Ports USB2.0 (Type A) x2 + SATA + PCIExpressx1
Interface PCI-Express X1 x1, SATA x1, Through Hall (Pin Header)
(UART x1, GPIO x2), I2C x1)
Flash ROM 256KB (NOR), 256MB (NAND)
Internal Bay 3.5” SATA-HDD Bay x1 Internal Cooling FAN
Power supply Input: AC110V (Internal)
Output: Max.25W (5V 1.5A, 12V 1.5A)

Software Specifications

Kurobox PRO
Boot Loader u-boot
Software Linux kernel 2.6.12
busybox , samba3.0 , mtd-utils , bash , xfs-progs, libtermcap , libncurses , glibc , gcc

Default Settings

Kurobox PRO
IP Settings
  • KURO-BOX/PRO Name: KUROBOX-PRO
  • IP Address: DHCP client
    (If there is no DHCP server, it will default to 192.168.11.150.)
Date and Time
  • Super Capacitor Backup
  • Initialized value : January 1, 1970
Root access
  • Console Administrator: root
  • Password: kuroadmin
SWAT
  • SWAT User: root
  • Password: kuroadmin
Samba Share Folder
  • Workgroup Name: KUROBOX
  • /mnt/mtd: mtd device (NAND FLASH),
  • /mnt/disk1: share (HDD)

UBoot/Linux Console Message - bootup

The Kurobox Pro has two internal serial port connection points - the default console output goes to UART0 at CN6. When this point is connected via Serial port to a terminal, the following bootup sequence is displayed when the front panel power button is pressed.

This boot sequence is for a Kurobox Pro with an 80GB SATA HDD.

One point of interest is the CPU clock @ 500Mhz

Orion1   CPU =  Low

=== KURO U-Boot. ===
 ** LOADER **
 ** KUROBOX BOARD: KURO_BOX  LE (CFG_ENV_ADDR=fffff000)

U-Boot 1.1.1 (Apr 10 2007 - 18:10:08) Marvell version: 1.12.1 - TINY

DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
NAND: 256 MB

Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 500Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz

USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Using 88E1118 phy
Found boot image
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0
<<system_bootend>>
Hit any key to stop autoboot:  0

Loading from device 0: <NULL> at 0xfa000000 (offset 0x20000)
   Image Name:   Linux-2.6.12.6-arm1
   Created:      2007-04-10  13:45:13 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1736548 Bytes =  1.7 MB
   Load Address: 00008000
   Entry Point:  00008000
<<stop_sound>>
## Booting image at 00100000 ...
   Image Name:   Linux-2.6.12.6-arm1
   Created:      2007-04-10  13:45:13 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1736548 Bytes =  1.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

arg:console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.091
CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX ---
Uncompressing Linux.................................................................................
................................ done, booting the kernel.
Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)
) #27 Tue Apr 10 22:47:16 JST 2007
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 250000000, Tclk = 166664740
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.091
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 126208KB available (3037K code, 426K data, 112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
serial_initialize_ttyS1 (Debug): ttyS1 is initialized.
 config_device_cs Error : Unknown board

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size   1MB
PCI0_MEM ....base e8000000, size 128MB
PCI0_IO ....base f2100000, size   1MB
INTER_REGS ....base f1000000, size   1MB
DEVICE_CS0 ....base fa000000, size   2MB
DEVICE_CS1 ....base f4000000, size  32MB
DEVICE_CS2 ....base fa800000, size   1MB
DEV_BOOCS ....base ff800000, size   8MB
CRYPTO ENG ....no such
Flash bankwidth 1, base ff800000, size 400000
KUROBOX FLASH size 4096[KB]

  Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_BOARD_KUROBOX  Soc: 88F5182
 A2

 Detected Tclk 166664740 and SysClk 250000000
Marvell USB EHCI Host controller #0: c04e4b00
Marvell USB EHCI Host controller #1: c04e4a40
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Use the XOR engines (offloading) for enhancing the following functions:
  o RAID 5 Xor calculation
  o kernel memcpy
  o kenrel memzero
  o copy user to/from kernel buffers
Number of XOR engines to use: 2
cesadev_init(c00122e4)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
inotify device minor=63
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
SGI XFS with no debug enabled
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
  o Ethernet descriptors in DRAM
  o DRAM SW cache-coherency
  o Checksum offload enabled
  o Loading network interface ** egiga_init_module (10)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
  Vendor: Maxtor    Model: 6Y080M0           Rev: YAR5
  Type:   Direct-Access                      ANSI SCSI revision: 03
SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB)
SCSI device sda: drive cache: write back
 sda: sda1
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
physmap flash device: 400000 at ff800000
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Debug nand_scan : nand_flash_ids[i].pagesize is exist
Debug nand_scan : mtd->erasesize=0x00020000
Debug nand_scan : mtd->oobblock=0x00000800
Debug nand_scan : mtd->oobsize=0x00000040
NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 21 at 0x002a0000
Using static partition definition
Creating 3 MTD partitions on "nand_mtd":
0x00000000-0x00400000 : "uImage"
0x00400000-0x04400000 : "rootfs"
0x04400000-0x10000000 : "extra"
usbmon: debugs is not available
ehci_platform ehci_platform.4523: EHCI Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: park 0
ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: park 0
ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.2
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
   arm4regs  :   304.000 MB/sec
   8regs     :   215.200 MB/sec
   32regs    :   249.200 MB/sec
raid5: using function: arm4regs (304.000 MB/sec)
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
Buffalo Platform Linux Driver(Light) 0.01 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Empty flash at 0x00df85f8 ends at 0x00df8800
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 112K
--- rcStart (NANDroot) ---
===== Starting MountSystemFolders =====
mounting procfs ... [Success]
mounting sysfs ... [Success]
mouting usbfs ... [Success]
remouting rootfs ... [Success]
mounting all devices ... [Success]

===== Starting checkroot.sh =====
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
[Success]

===== Starting Kevent.sh =====
[Success]

===== Starting mount_share.sh =====
Mounting /dev/sda1 on /mnt/disk1 as a xfs file system.
XFS mounting filesystem sda1
Starting XFS recovery on filesystem: sda1 (dev: sda1)
Ending XFS recovery on filesystem: sda1 (dev: sda1)
Success.

Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system.
Success.

[Success]

===== Starting sethostname.sh =====
hostname is setted to KUROBOX-PRO
[Success]

===== Starting networking.sh =====
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP  tout=30[s]
eth0: link down
eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>
/etc/dhcpc/dhcpcd.exe ::: /etc/dhcpc/dhcpcd-eth0.info up
dhcpcd.exe: interface eth0 has been configured with old IP=192.168.1.151
hostname is setted to KUROBOX-PRO
[Success]

===== Starting httpd.sh =====
[Success]

===== Starting telnet.sh =====
[Success]

===== Starting inetd.sh =====
[Success]

===== Starting smb.sh =====
$Starting SMB services:
$Starting NMB services:
[Success]

===== Starting clientUtil_servd.sh =====
Starting clientUtil_server:starting on eth0
[Success]

===== Starting bootcomplete.sh =====
[Success]

===== Starting FanController.sh =====
[Success]

===== Starting boss.sh =====
                           ...''''..
               '-~~(~~'' .~<shDBDhz+(-.
            .~+sDDBNBDhhszDBNNNNBNNNBDs<-
           ~sBNNNNNNNNNNNNNNNNNNNNNNNNNBs<'
         -=DNNBNNNNNNNNNNNNNNNNNBNNNNNNNNBz<'
       .~zNNNNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNNz~
      '~hBNNNNBNNNNNNNNNNNNNNNNNNNNNNNNNNNNNND+'
      (hNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNBs-
    .~zNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNBNNBNNNNNNBs
    ~sBNNNNNNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNNNNNNNNz
   (+DNNNNNNNNNNNNNNNNNNNNNNDzNNNNNhzDNNBNNNNNNNNBs
   (sNNNNNNNNNNNNNNNNNNNNNNB=~hNNNN=~(sDNNNNNNNNNND
  (+DNNNNNNNNNNNNNNNNNNNNNNs'.=NNNNz- '(zDNNNNNNNNNz
  ~=BNNNNNNNNNNNNNNNNNNNNND- .=BNNNN<.  .(hNNNNNNNNB
  ~sNNNNNNNNNNNNNNNNNNNNND+. .+BNNNN+'    ~sBNNNNNNN
  (zNNNNNNNNNNNNNNNNNNNNND' ..+BNBNB=-     .+BNNNNNNh
  (zNNNNNNNNNNNNNNNNNNNBB= . 'hNBBNs+-      '+DNNNBND
  (sNNNNNNNNNNNNNNNNNNNND(   -DhDBN+<-    .  '=NNNNNB
  ~+DNNBNNNNNNNNNNNNNNNNz'  '=D=Dhh+('      . ~DBNNNB
  ~(sNNNNNNNNNNNNNNNNNNNz.  -hs(zz+<('      . .=NNNNN
   ~=NNBBBBNNNNNNNNNNNNB=  '==-=+s((~.        .~BNNNB
   ~=Nhs<+++hNNNNNNNNBz<- .~=-.s(+-(-          'hBNND
    =Ds+hz( ~hNNNNNNND+'..-+'.-((('<~''...     -hNNNNDs
   ~+z(BN=. .<BNNNNBhhDD=+<~. ~-=shBBDhz+('   -sBNNNBBNBz
  ~(=z(BD- '~~hBNNNs~-(<zDDs+~(shzssszDBNDh=<<sBNNNNNNNBN
  ~~+s<z=.-zh~sNNND<.  .''<zhhh==shDBNNNNNNNBDDNNNNNNNNNh
  ~~<ss+<.zBBs~zND+'      ..-+zDBNNNNNNNNNNNhzNNNNNNNNND+
  ~~(=h<<'+DBz-sBs~         .  (BBNNNNNNNNNz-<BBNNBNNND=
  ~(~<zss(('(z<sD+'            ~DNNNNNNNNNz~ 'sNNNNNNDs
    ~(=Ds=<...-(h<.    .     ..<BNNNNNNNNz~   -hNNNBh
     ~(hNs(.    =-            .=BNNNNNBNs-    .(hs==
     ''<BNz~    '.            .(hBNNBDz<'      .~''-
       -hNNh(. '..             .'<<(++~   .     -''.
       'hBNB+' '                   -+('.       .-''.
       'zDNz(  '.                 ~+<-'''..''. .-.
       ..~(-.  .'.              .~+(.   ..''--''.
                ''.           .'+<~         '~.
               .....          .-' .'---(~~~(<~.
                 ..'.            .((---'-~~(~
                   .'.            '+s=(-'-(+.   < Let's start a KURO-BOX!
                    ....           .(hBDzDD=.       and have a fun time...
                     ..'..          .'<sDh+.
                       .''..       .   ..-- .
                         ..''..         ...
                           .......     .'.
                              ..''..'-'..
                                  ...
[Success]

KUROUTOSHIKOU KUROBOX Series KUROBOX/PRO(KOSHO)
KUROBOX-PRO login:

Console Message - shutdown

During shutdown, initiated by front panel button push, the following console message is displayed at UART0.

----- rcDown -----

===== Starting shutdown_start.sh =====
[Success]

===== Starting shutdown_proc.sh =====

===== Starting clientUtil_servd.sh =====
Stop clientUtil_server:[Success]

===== Starting smb.sh =====
$Shutting down SMB services:
$Shutting down NMB services:
[Success]

===== Starting networking.sh =====
Deconfiguration network interface: lo eth0
[Success]

===== Starting Kevent.sh =====
[Success]

===== Starting FanController.sh =====
Stopping a fan ...........
[Success]

[Success]

===== Starting umount_disk.sh =====
[Success]

The system is going down NOW !!
Sending SIGTERM to all processes.
Sending SIGKILL to all processes.
The system is halted.
md: stopping all md devices.
md: md0 switched to read-only mode.
Synchronizing SCSI cache for disk sda:
System halted.

Accessing Partions from Samba

There is no FTPd to ftp files into the KuroBox at this point. But there is Samba!

The flash memory is available at

smb://kuroip/mtd_device

The newly installed hard drive is at

smb://kuroip/share

You could stop here if you wanted to, after all you have a network share with samba/swat for administration.

Install a root file system (Distribution)

The following procedure creates the following partition scheme, and untars a root file system onto p2 (/dev/sda2). Somehow it rewrites the uboot variables allowing a boot from the hard drive. Console access would be the preferred way to change these uboot settings. Netcat does not seem to work to access uboot. Serial Console access would be a must [1].


  1. p1 : /boot (16MB)
  2. p2 : /rootfs (3GB)
  3. p4 : extend (others)
  4. p5 : swap (128MB)
  5. p6 : /share (others)
Nuvola apps important.png 
WARNING!

The provided documentation says that this process is not recommended.



Buffalo Provided Developer System

  1. Connect up the blank unformatted hard drive and power on.
  2. Access the Samba share on the kurobox named mtd_device
  3. Copy over these files to the samba share from the provided CD-ROM
    1. hddrootfs.tar.gz (this file probably could be replaced with an alternate rootfs, see below)
    2. ChangeMeDevHDD
    3. ChangeMyUbootEnv
    4. uImage.buffalo
  4. Press the red init button on the back till it beeps
  5. The Info LED will flash the drive will be partitoned to the above scheme, afterwards the above partition scheme was created and hddrootfs.tar.gz was untarred into /dev/sda2
  6. Reboot System.

GenLink (Gentoo)

Kurobrick.png
WARNING!

There is a possibility that you could brick your NAS with these instructions. Please make sure that you read the entire page carefully. this is as of yet untested

I think you could use this method to install GenLink, although I'm not sure that 3GB is a large enough root file space

  1. Connect up the blank unformatted hard drive and power on.
  2. Access the Samba share on the kurobox named mtd_device
  3. Download the GenLink Tarball: http://downloads.linkstationwiki.net/LSPro_ARM9/Distributions/Genlink/Rootfs/GenLink_arm9-1.0pre6-20070227.tar.bz2
  4. Then rename it to hddrootfs.tar.gz and copy it over to the Samba Share
  5. Copy over these files to the samba share from the provided CD-ROM
    1. ChangeMeDevHDD
    2. ChangeMyUbootEnv
    3. uImage.buffalo
  6. Press the red init button on the back till it beeps
  7. The Info LED will flash and the drive will be partitoned and Genlink Installed
  8. Reboot System.
  9. Then follow the directions for the First boot of the new GenLink rootfs

FreeLink (Debian)

Kurobrick.png
WARNING!

There is a possibility that you could brick your NAS with these instructions. Please make sure that you read the entire page carefully. this is as of yet untested, however the method has been reported to work by a few japanese kuroboxpro users.


  1. Connect up the blank unformatted hard drive and power on.
  2. Access the Samba share on the kurobox named mtd_device
  3. Download the FreeLink zip archive: http://downloads.linkstationwiki.net/LSPro_ARM9/Distributions/Freelink/FreeLink_arm9-1.0rev2.zip
  4. Unzip it and find the hddrootfs.img file
  5. Rename it to have the .tgz extension
  6. Extract this file with the following password:
    IeY8omJwGlGkIbJm2FH_MV4fLsXE8ieu0gNYwE6Ty
  7. Rename the resultant file tohddrootfs.tar.gz and copy it over to the Samba Share
  8. Copy over these files to the samba share from the provided CD-ROM
    1. ChangeMeDevHDD
    2. ChangeMyUbootEnv
    3. uImage.buffalo
  9. Press the red init button on the back till it beeps
  10. The Info LED will flash and the drive will be partitoned and FreeLink Installed
  11. Reboot and use ssh to login to your newly FreeLinked KuroBox Pro with login:root and password:lspro
  12. You will now need to change a line in the the /usr/local/sbin/kernelmon script: "cat /proc/driver/kernevnt" to "cat /proc/buffalo/kernevnt".
  13. Remember to change the /etc/fstab to reflect the location of linux swap
  14. Then follow the directions for FreeLink for the Linkstation Pro: Update of the debian packages

Japanese Kuro-Box Interface

Webserver

http://kuroip

gives

Kuro.gif

linked to http://www.kuroutoshikou.com/


this could be changed the index.html and gif is in:

./www:
drw-r--r--    3 root     root            0 Feb  9 10:17 .
drwxr-xr-x   18 root     root            0 May 23 01:57 ..
drwxrwxrwx    2 root     root            0 Feb  9 22:35 img
-rwxrwxrwx    1 root     root           95 Feb  9 10:17 index.html

./www/img:
drwxrwxrwx    2 root     root            0 Feb  9 22:35 .
drw-r--r--    3 root     root            0 Feb  9 10:17 ..
-rwxrwxrwx    1 root     root         4587 Feb  9 22:35 kuro.gif

Starting Beep

The KuroPro makes a distinctive starting beep. You can use the beeper to play sounds at any time if you want it uses miconapl


PlayBeep.sh /usr/local/music/SW_ON.msc 


/usr/local/bin/Playbeep.sh

#!/bin/sh

if [ -f "$1" ] ; then
        TEMPO=`grep "TEMPO=" $1|sed -e "s/TEMPO=//"`
        MELODY=`grep -v "TEMPO=" $1`
        PLAYDATA="${TEMPO} ${MELODY}"
else
        MELODY=`echo $*| sed -e "s/$0//"`
        PLAYDATA=${MELODY}
fi

miconapl -a bz_melody ${PLAYDATA}

/usr/local/music/SW_ON.msc

TEMPO=30
b4 b5 b4 b6


dmesg

These are from a Japanese Kuro Pro the American and European versions may be different

/mnt/mtd # dmesg
pj=1331200)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
serial_initialize_ttyS1 (Debug): ttyS1 is initialized.
 config_device_cs Error : Unknown board 

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB 
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB 
PEX0_IO ....base f2000000, size   1MB 
PCI0_MEM ....base e8000000, size 128MB 
PCI0_IO ....base f2100000, size   1MB 
INTER_REGS ....base f1000000, size   1MB 
DEVICE_CS0 ....base fa000000, size   2MB 
DEVICE_CS1 ....base f4000000, size  32MB 
DEVICE_CS2 ....base fa800000, size   1MB 
DEV_BOOCS ....base ff800000, size   8MB 
CRYPTO ENG ....no such
Flash bankwidth 1, base ff800000, size 400000
KUROBOX FLASH size 4096[KB]

  Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_BOARD_KUROBOX  Soc: 88F5182 A2

 Detected Tclk 166664740 and SysClk 250000000 
Marvell USB EHCI Host controller #0: c04e4b00
Marvell USB EHCI Host controller #1: c04e4a40
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Use the XOR engines (offloading) for enhancing the following functions:
  o RAID 5 Xor calculation
  o kernel memcpy
  o kenrel memzero
  o copy user to/from kernel buffers
Number of XOR engines to use: 2
cesadev_init(c00122e4)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
inotify device minor=63
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
SGI XFS with no debug enabled
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
  o Ethernet descriptors in DRAM
  o DRAM SW cache-coherency
  o Checksum offload enabled
  o Loading network interface ** egiga_init_module (10)
'eth0' 
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
physmap flash device: 400000 at ff800000
CFI: Found no phys_mapped_flash device at location zero
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
phys_mapped_flash: Found an alias at 0x40000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x80000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0xc0000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x100000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x140000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x180000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x1c0000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x200000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x240000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x280000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x2c0000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x300000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x340000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x380000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x3c0000 for the chip at 0x0
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Debug nand_scan : nand_flash_ids[i].pagesize is exist
Debug nand_scan : mtd->erasesize=0x00020000
Debug nand_scan : mtd->oobblock=0x00000800
Debug nand_scan : mtd->oobsize=0x00000040
NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Using static partition definition
Creating 3 MTD partitions on "nand_mtd":
0x00000000-0x00400000 : "uImage"
0x00400000-0x04400000 : "rootfs"
0x04400000-0x10000000 : "extra"
usbmon: debugs is not available
ehci_platform ehci_platform.4523: EHCI Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: park 0
ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: park 0
ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v2.2
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
   arm4regs  :   309.200 MB/sec
   8regs     :   217.600 MB/sec
   32regs    :   252.400 MB/sec
raid5: using function: arm4regs (309.200 MB/sec)
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
Buffalo Platform Linux Driver(Light) 0.01 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Empty flash at 0x00df85f8 ends at 0x00df8800
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 112K
jffs2_get_inode_nodes(): Data CRC failed on node at 0x01dc1308: Read 0xca66d714, calculated 0xc26a5721
eth0: link down
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>


File Structure

http://www.kurobox.com/mwiki/images/b/b4/Kuroboxprofilestructure.txt

Uboot Settings

Marvell>> printenv At the time of Flash starting

baudrate=115200
loads_echo=0
ipaddr=192.168.11.150
serverip=192.168.11.1
rootpath=/nfs/arm
cpuName=926
CASset=min
MALLOC_len=4
bootargs_end=:::DB88FXX81:eth0:none
ethact=egiga0
ethaddr=00:16:01:A4:C2:4A
buffalo_ver=BOOTVER=1.091
build_time=15:59:38
initrd=initrd.buffalo
kernel=uImage.buffalo
bootargs_base=console=ttyS0,115200
bootargs_root=root=/dev/mtdblock2 rw panic=5
bootargs=$(bootargs_base) $(bootargs_root) $(buffalo_ver)
nand_uImage_offset=20000
default_kernel_addr=0x00100000
default_initrd_addr=0x02000000
def_tftp=tftp $(default_kernel_addr) $(kernel); tftp $(default_initrd_addr) $(initrd); setenv bootargs $(bootargs_base) $(bootargs_root)  rw initrd=0x02000040,20M panic=5 $(buffalo_ver); bootm $(default_kernel_addr) $(default_initrd_addr)
nand_boot=yes
stdin=serial
stdout=serial
stderr=serial
enaMonExt=no
enaFlashBuf=yes
enaCpuStream=no
ethprime=egiga0
bootdelay=3
disaMvPnp=no
overEthAddr=no
usb0Mode=host
usb1Mode=host
force_tftp=1
bootcmd=tftp $(default_kernel_addr) $(kernel); tftp $(default_initrd_addr) $(initrd); setenv bootargs $(bootargs_base) $(bootargs_root)  rw initrd=0x02000040,20M panic=5 $(buffalo_ver); bootm $(default_kernel_addr) $(default_initrd_addr)

Environment size: 1192/4092 bytes

Marvell>> printenv At the time of HDD starting

baudrate=115200
loads_echo=0
ipaddr=192.168.11.150
serverip=192.168.11.1
rootpath=/nfs/arm
cpuName=926
CASset=min
MALLOC_len=4
bootargs_end=:::DB88FXX81:eth0:none
ethact=egiga0
ethaddr=00:16:01:A4:C2:4A
buffalo_ver=BOOTVER=1.091
build_time=15:59:38
initrd=initrd.buffalo
kernel=uImage.buffalo
bootargs_base=console=ttyS0,115200
bootargs_root=root=/dev/sda2 rw panic=5
bootargs=console=ttyS0,115200 root=/dev/sda2 rw panic=5 BOOTVER=1.09
nand_uImage_offset=20000
default_kernel_addr=0x00100000
default_initrd_addr=0x02000000
def_tftp=tftp $(default_kernel_addr) $(kernel); tftp $(default_initrd_addr) $(initrd); setenv bootargs $(bootargs_base) $(bootargs_root)  rw initrd=0x02000040,20M panic=5 $(buffalo_ver); bootm $(default_kernel_addr) $(default_initrd_addr)
nand_boot=no
stdin=serial
stdout=serial
stderr=serial
enaMonExt=no
enaFlashBuf=yes
enaCpuStream=no
ethprime=egiga0
bootdelay=3
disaMvPnp=no
overEthAddr=no
usb0Mode=host
usb1Mode=host
force_tftp=1
bootcmd=tftp $(default_kernel_addr) $(kernel); tftp $(default_initrd_addr) $(initrd); setenv bootargs $(bootargs_base) $(bootargs_root)  rw initrd=0x02000040,20M panic=5 $(buffalo_ver); bootm $(default_kernel_addr) $(default_initrd_addr)

Environment size: 1197/4092 bytes

References

Kurobox Pro microprocessor interface specifications