Kurobox Pro UBoot/Linux Console Message - bootup
UBoot/Linux Console Message - bootup
The Kurobox Pro has two internal serial port connection points - the default console output goes to UART0 at CN6. When this point is connected via Serial port to a terminal, the following bootup sequence is displayed when the front panel power button is pressed.
This boot sequence is for a Kurobox Pro with an 80GB SATA HDD.
One point of interest is the CPU clock @ 500Mhz
Orion1 CPU = Low === KURO U-Boot. === ** LOADER ** ** KUROBOX BOARD: KURO_BOX LE (CFG_ENV_ADDR=fffff000) U-Boot 1.1.1 (Apr 10 2007 - 18:10:08) Marvell version: 1.12.1 - TINY DRAM CS base 0x00000000 size 128MB DRAM Total size 128MB [256kB@fffc0000] Flash: 256 kB Addresses 20M - 0M are saved for the U-Boot usage. Mem malloc Initialization (20M - 16M): Done NAND: 256 MB Soc: 88F5182 A2 CPU: ARM926 (Rev 0) running @ 500Mhz Orion 1 streaming disabled SysClock = 250Mhz , TClock = 166Mhz USB 0: host mode USB 1: host mode PCI 0: PCI Express Root Complex Interface PCI 1: Conventional PCI, speed = 33000000 Net: egiga0 [PRIME] Using 88E1118 phy Found boot image hit any key to switch tftp boot. Hit any key to stop autoboot: 0 <<system_bootend>> Hit any key to stop autoboot: 0 Loading from device 0: <NULL> at 0xfa000000 (offset 0x20000) Image Name: Linux-184.108.40.206-arm1 Created: 2007-04-10 13:45:13 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1736548 Bytes = 1.7 MB Load Address: 00008000 Entry Point: 00008000 <<stop_sound>> ## Booting image at 00100000 ... Image Name: Linux-220.127.116.11-arm1 Created: 2007-04-10 13:45:13 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1736548 Bytes = 1.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... arg:console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.091 CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX --- Uncompressing Linux................................................................................. ................................ done, booting the kernel. Linux version 18.104.22.168-arm1 (root@dev-hara) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2) ) #27 Tue Apr 10 22:47:16 JST 2007 CPU: ARM926EJ-Sid(wb)  revision 0 (ARMv5TEJ) CPU0: D VIVT write-back cache CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets Machine: MV-88fxx81 Using UBoot passing parameters structure Sys Clk = 250000000, Tclk = 166664740 Memory policy: ECC disabled, Data cache writeback Built 1 zonelists Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.091 PID hash table entries: 1024 (order: 10, 16384 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 128MB 0MB 0MB 0MB = 128MB total Memory: 126208KB available (3037K code, 426K data, 112K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 serial_initialize_ttyS1 (Debug): ttyS1 is initialized. config_device_cs Error : Unknown board CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 128MB SDRAM_CS1 ....disable SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base e0000000, size 128MB PEX0_IO ....base f2000000, size 1MB PCI0_MEM ....base e8000000, size 128MB PCI0_IO ....base f2100000, size 1MB INTER_REGS ....base f1000000, size 1MB DEVICE_CS0 ....base fa000000, size 2MB DEVICE_CS1 ....base f4000000, size 32MB DEVICE_CS2 ....base fa800000, size 1MB DEV_BOOCS ....base ff800000, size 8MB CRYPTO ENG ....no such Flash bankwidth 1, base ff800000, size 400000 KUROBOX FLASH size 4096[KB] Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_BOARD_KUROBOX Soc: 88F5182 A2 Detected Tclk 166664740 and SysClk 250000000 Marvell USB EHCI Host controller #0: c04e4b00 Marvell USB EHCI Host controller #1: c04e4a40 pexBarOverlapDetect: winNum 2 overlap current 0 mvPexInit:Warning :Bar 2 size is illigal it will be disabled please check Pex and CPU windows configuration PCI: bus0: Fast back to back transfers enabled PCI: bus1: Fast back to back transfers enabled SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub Use the XOR engines (offloading) for enhancing the following functions: o RAID 5 Xor calculation o kernel memcpy o kenrel memzero o copy user to/from kernel buffers Number of XOR engines to use: 2 cesadev_init(c00122e4) Fast Floating Point Emulator V0.9 (c) Peter Teichmann. inotify device minor=63 JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc. SGI XFS with no debug enabled Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled ttyS0 at MMIO 0x0 (irq = 3) is a 16550A ttyS1 at MMIO 0x0 (irq = 4) is a 16550A io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize loop: loaded (max 8 devices) Marvell Gigabit Ethernet Driver 'egiga': o Ethernet descriptors in DRAM o DRAM SW cache-coherency o Checksum offload enabled o Loading network interface ** egiga_init_module (10) 'eth0' Intergrated Sata device found scsi0 : Marvell SCSI to SATA adapter scsi1 : Marvell SCSI to SATA adapter Vendor: Maxtor Model: 6Y080M0 Rev: YAR5 Type: Direct-Access ANSI SCSI revision: 03 SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB) SCSI device sda: drive cache: write back SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB) SCSI device sda: drive cache: write back sda: sda1 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0 physmap flash device: 400000 at ff800000 Found: SST 39LF020 phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank number of JEDEC chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. RedBoot partition parsing not available Debug nand_scan : nand_flash_ids[i].pagesize is exist Debug nand_scan : mtd->erasesize=0x00020000 Debug nand_scan : mtd->oobblock=0x00000800 Debug nand_scan : mtd->oobsize=0x00000040 NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 21 at 0x002a0000 Using static partition definition Creating 3 MTD partitions on "nand_mtd": 0x00000000-0x00400000 : "uImage" 0x00400000-0x04400000 : "rootfs" 0x04400000-0x10000000 : "extra" usbmon: debugs is not available ehci_platform ehci_platform.4523: EHCI Host Controller ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1 ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000 ehci_platform ehci_platform.4523: park 0 ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ehci_platform ehci_platform.16781: EHCI Host Controller ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2 ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000 ehci_platform ehci_platform.16781: park 0 ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected USB Universal Host Controller Interface driver v2.2 Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.01:USB HID core driver mice: PS/2 mouse device common for all mice md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid5 personality registered as nr 4 raid5: measuring checksumming speed arm4regs : 304.000 MB/sec 8regs : 215.200 MB/sec 32regs : 249.200 MB/sec raid5: using function: arm4regs (304.000 MB/sec) md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 Buffalo Platform Linux Driver(Light) 0.01 installed. MICON ctrl (C) BUFFALO INC. V.1.00 installed. Kernel event proc (C) BUFFALO INC. V.1.00 installed. MICON V2 (C) BUFFALO INC. V.1.00 installed. NET: Registered protocol family 2 IP: routing cache hash table of 1024 buckets, 8Kbytes TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) NET: Registered protocol family 1 NET: Registered protocol family 17 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. Empty flash at 0x00df85f8 ends at 0x00df8800 VFS: Mounted root (jffs2 filesystem). Freeing init memory: 112K --- rcStart (NANDroot) --- ===== Starting MountSystemFolders ===== mounting procfs ... [Success] mounting sysfs ... [Success] mouting usbfs ... [Success] remouting rootfs ... [Success] mounting all devices ... [Success] ===== Starting checkroot.sh ===== rm: /var/lock/perfmon: is a directory rm: /var/lock/printing: is a directory rm: /var/lock/subsys: is a directory [Success] ===== Starting Kevent.sh ===== [Success] ===== Starting mount_share.sh ===== Mounting /dev/sda1 on /mnt/disk1 as a xfs file system. XFS mounting filesystem sda1 Starting XFS recovery on filesystem: sda1 (dev: sda1) Ending XFS recovery on filesystem: sda1 (dev: sda1) Success. Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system. Success. [Success] ===== Starting sethostname.sh ===== hostname is setted to KUROBOX-PRO [Success] ===== Starting networking.sh ===== create network files.. IP=[dhcp], netmask=, dgw=, dns1=, dns2= killall: dhcpcd: no process killed route: SIOC[ADD|DEL]RT: No such process Configuration network interface: lo eth0 requesting DHCP tout=30[s] eth0: link down eth0: link up<5>, full duplex<5>, speed 100 Mbps<5> /etc/dhcpc/dhcpcd.exe ::: /etc/dhcpc/dhcpcd-eth0.info up dhcpcd.exe: interface eth0 has been configured with old IP=192.168.1.151 hostname is setted to KUROBOX-PRO [Success] ===== Starting httpd.sh ===== [Success] ===== Starting telnet.sh ===== [Success] ===== Starting inetd.sh ===== [Success] ===== Starting smb.sh ===== $Starting SMB services: $Starting NMB services: [Success] ===== Starting clientUtil_servd.sh ===== Starting clientUtil_server:starting on eth0 [Success] ===== Starting bootcomplete.sh ===== [Success] ===== Starting FanController.sh ===== [Success] ===== Starting boss.sh ===== ...''''.. '-~~(~~'' .~<shDBDhz+(-. .~+sDDBNBDhhszDBNNNNBNNNBDs<- ~sBNNNNNNNNNNNNNNNNNNNNNNNNNBs<' -=DNNBNNNNNNNNNNNNNNNNNBNNNNNNNNBz<' .~zNNNNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNNz~ '~hBNNNNBNNNNNNNNNNNNNNNNNNNNNNNNNNNNNND+' (hNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNBs- .~zNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNBNNBNNNNNNBs ~sBNNNNNNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNNNNNNNNz (+DNNNNNNNNNNNNNNNNNNNNNNDzNNNNNhzDNNBNNNNNNNNBs (sNNNNNNNNNNNNNNNNNNNNNNB=~hNNNN=~(sDNNNNNNNNNND (+DNNNNNNNNNNNNNNNNNNNNNNs'.=NNNNz- '(zDNNNNNNNNNz ~=BNNNNNNNNNNNNNNNNNNNNND- .=BNNNN<. .(hNNNNNNNNB ~sNNNNNNNNNNNNNNNNNNNNND+. .+BNNNN+' ~sBNNNNNNN (zNNNNNNNNNNNNNNNNNNNNND' ..+BNBNB=- .+BNNNNNNh (zNNNNNNNNNNNNNNNNNNNBB= . 'hNBBNs+- '+DNNNBND (sNNNNNNNNNNNNNNNNNNNND( -DhDBN+<- . '=NNNNNB ~+DNNBNNNNNNNNNNNNNNNNz' '=D=Dhh+(' . ~DBNNNB ~(sNNNNNNNNNNNNNNNNNNNz. -hs(zz+<(' . .=NNNNN ~=NNBBBBNNNNNNNNNNNNB= '==-=+s((~. .~BNNNB ~=Nhs<+++hNNNNNNNNBz<- .~=-.s(+-(- 'hBNND =Ds+hz( ~hNNNNNNND+'..-+'.-((('<~''... -hNNNNDs ~+z(BN=. .<BNNNNBhhDD=+<~. ~-=shBBDhz+(' -sBNNNBBNBz ~(=z(BD- '~~hBNNNs~-(<zDDs+~(shzssszDBNDh=<<sBNNNNNNNBN ~~+s<z=.-zh~sNNND<. .''<zhhh==shDBNNNNNNNBDDNNNNNNNNNh ~~<ss+<.zBBs~zND+' ..-+zDBNNNNNNNNNNNhzNNNNNNNNND+ ~~(=h<<'+DBz-sBs~ . (BBNNNNNNNNNz-<BBNNBNNND= ~(~<zss(('(z<sD+' ~DNNNNNNNNNz~ 'sNNNNNNDs ~(=Ds=<...-(h<. . ..<BNNNNNNNNz~ -hNNNBh ~(hNs(. =- .=BNNNNNBNs- .(hs== ''<BNz~ '. .(hBNNBDz<' .~''- -hNNh(. '.. .'<<(++~ . -''. 'hBNB+' ' -+('. .-''. 'zDNz( '. ~+<-'''..''. .-. ..~(-. .'. .~+(. ..''--''. ''. .'+<~ '~. ..... .-' .'---(~~~(<~. ..'. .((---'-~~(~ .'. '+s=(-'-(+. < Let's start a KURO-BOX! .... .(hBDzDD=. and have a fun time... ..'.. .'<sDh+. .''.. . ..-- . ..''.. ... ....... .'. ..''..'-'.. ... [Success] KUROUTOSHIKOU KUROBOX Series KUROBOX/PRO(KOSHO) KUROBOX-PRO login:
Console Message - shutdown
During shutdown, initiated by front panel button push, the following console message is displayed at UART0.
----- rcDown ----- ===== Starting shutdown_start.sh ===== [Success] ===== Starting shutdown_proc.sh ===== ===== Starting clientUtil_servd.sh ===== Stop clientUtil_server:[Success] ===== Starting smb.sh ===== $Shutting down SMB services: $Shutting down NMB services: [Success] ===== Starting networking.sh ===== Deconfiguration network interface: lo eth0 [Success] ===== Starting Kevent.sh ===== [Success] ===== Starting FanController.sh ===== Stopping a fan ........... [Success] [Success] ===== Starting umount_disk.sh ===== [Success] The system is going down NOW !! Sending SIGTERM to all processes. Sending SIGKILL to all processes. The system is halted. md: stopping all md devices. md: md0 switched to read-only mode. Synchronizing SCSI cache for disk sda: System halted.