Kurobox Pro u-boot environment variable settings
From NAS-Central Buffalo - The Linkstation Wiki
(Difference between revisions)
m |
m |
||
| Line 1: | Line 1: | ||
{{Articles|KuroboxPro}} | {{Articles|KuroboxPro}} | ||
| + | ==FLASH BOOT== | ||
===Boot settings when uImage(nand /dev/mtdblock1), rootfs(nand /dev/mtdblock2)=== | ===Boot settings when uImage(nand /dev/mtdblock1), rootfs(nand /dev/mtdblock2)=== | ||
| Line 25: | Line 26: | ||
</pre> | </pre> | ||
| + | ==HARD DRIVE BOOT== | ||
===Boot settings when uImage(nand /dev/mtdblock1), rootfs(/dev/sda2)=== | ===Boot settings when uImage(nand /dev/mtdblock1), rootfs(/dev/sda2)=== | ||
| Line 72: | Line 74: | ||
</pre> | </pre> | ||
| + | ==TFTP BOOT== | ||
===Boot settings when uImage(tftp load), rootfs(nand /dev/mtdblock2)=== | ===Boot settings when uImage(tftp load), rootfs(nand /dev/mtdblock2)=== | ||
Revision as of 05:06, 24 August 2007
Contents |
FLASH BOOT
Boot settings when uImage(nand /dev/mtdblock1), rootfs(nand /dev/mtdblock2)
| uImage | /dev/mtdblock1 (0x00020000~0x00400000)
4MB arrangement excluding head 128KB |
| initrd | ----- (Not use) |
| rootfs | /dev/mtdblock2 |
u-boot environment variable settings
setenv default_kernel_addr 0x00100000 setenv bootargs_base console=ttyS0,115200 setenv bootargs_root root=/dev/mtdblock2 rw setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) setenv uImage_block 0 setenv uImage_offset 0x00020000 setenv bootcmd ‘nboot $(default_kernel_addr) $(uImage_block) $(uImage_offset); bootm $(default_kernel_addr)’
HARD DRIVE BOOT
Boot settings when uImage(nand /dev/mtdblock1), rootfs(/dev/sda2)
| uImage | /dev/mtdblock1 (0x00020000~0x00400000)
4MB arrangement excluding head 128KB |
| initrd | -----(Not use) |
| rootfs | /dev/sda2 |
u-boot environment settings
setenv default_kernel_addr 0x00100000 setenv bootargs_base console=ttyS0,115200 setenv bootargs_root root=/dev/sda2 rw setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) setenv uImage block 0 setenv uImage_offset 0x00020000 setenv bootcmd ‘nboot $(default_kernel_addr) $(uImage_block) $(uImage_offset); bootm $(default_kernel_addr)’
Boot settings when uImage(/dev/sda1), rootfs(/dev/sda2)
| uImage | /dev/sda1 |
| initrd | -----(Not use) |
| rootfs | /dev/sda2 |
| Notes |
|
u-boot environment settings
setenv default_kernel_addr 0x00100000 setenv bootargs_base console=ttyS0,115200 setenv bootargs_root root=/dev/sda2 rw setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) setenv bootcmd ‘ext2load ide 0:1 $(default_kernel_addr)/$(kernel); bootm $(default_kernel_addr)’
TFTP BOOT
Boot settings when uImage(tftp load), rootfs(nand /dev/mtdblock2)
| uImage | Load from tftp |
| initrd | -----(Not use) |
| rootfs | /dev/mtdblock2 |
| tftpserver | (e.g.) 192.168.11.100 |
| KUROBOX-PRO | (e.g.) 192.168.11.150 |
| Notes |
|
u-boot environment variable settings
setenv default_kernel_addr 0x00100000 setenv bootargs_base console=ttyS0,115200 setenv bootargs_root root=/dev/mtdblock2 rw setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) setenv serverip 192.168.11.100 setenv ipaddr 192.168.11.150 setenv bootcmd ‘tftp $(default_kernel_addr) $(kernel); bootm $(default_kernel_addr)
Boot settings when uImage(tftp load), initrd(tftp load)
| uImage | Load from tftp |
| initrd | Load from tftp |
| rootfs | Exists in initrd |
| tftpserver (e.g.) | 192.168.11.100 |
| KUROBOX-PRO (e.g.) | 192.168.11.150 |
| Notes |
|
u-boot environment variable settings
setenv default_kernel_addr 0x00100000 setenv default_initrd_addr 0x02000000 setenv bootargs_base console=ttyS0,115200 setenv bootargs_root root=/dev/mtdblock2 rw setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) setenv serverip 192.168.11.100 setenv ipaddr 192.168.11.150 setenv bootcmd ‘tftp $(default_kernel_addr) $(kernel); tftp $(default_initrd_addr) $(initrd); bootm$(default_kernel_addr) $(default_initrd_addr)’
