Kurobox Pro u-boot environment variable settings

From NAS-Central Buffalo - The Linkstation Wiki

(Difference between revisions)
Jump to: navigation, search
(→u-boot environment settings)
m (→Boot settings when uImage(/dev/sda1), rootfs(/dev/sda2))
 
(7 intermediate revisions not shown)
Line 1: Line 1:
-
{{Articles|KuroboxPro}}
+
{{Articles|KuroboxPro|UBoot}}
 +
 
 +
==CHANGING U-BOOT SETTINGS==
 +
use "setenv ... " as shown below, check with "printenv", then save to flash with "saveenv".
==FLASH BOOT==
==FLASH BOOT==
Line 26: Line 29:
</pre>
</pre>
-
===[http://karlo.homedns.org/mt/kuroboxpro/printenv.log Marvell>> printenv At the time of Flash starting]===
+
===[http://kuroutoshikou.com/products/kuro_box_pro/u-boot-initienv.txt Marvell>> environment at the time of Flash starting]===
<pre>
<pre>
baudrate=115200
baudrate=115200
Line 33: Line 36:
serverip=192.168.11.1
serverip=192.168.11.1
rootpath=/nfs/arm
rootpath=/nfs/arm
 +
stdin=serial
 +
stdout=serial
 +
stderr=serial
cpuName=926
cpuName=926
CASset=min
CASset=min
 +
enaMonExt=no
 +
enaFlashBuf=yes
 +
enaCpuStream=no
MALLOC_len=4
MALLOC_len=4
 +
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
bootargs_end=:::DB88FXX81:eth0:none
-
ethact=egiga0
 
-
ethaddr=00:16:01:A4:C2:4A
 
buffalo_ver=BOOTVER=1.091
buffalo_ver=BOOTVER=1.091
-
build_time=15:59:38
+
build_time=18:10:02
initrd=initrd.buffalo
initrd=initrd.buffalo
kernel=uImage.buffalo
kernel=uImage.buffalo
Line 49: Line 57:
default_kernel_addr=0x00100000
default_kernel_addr=0x00100000
default_initrd_addr=0x02000000
default_initrd_addr=0x02000000
-
def_tftp=tftp $(default_kernel_addr) $(kernel); tftp $(default_initrd_addr) $(initrd); setenv bootargs $(bootargs_base) $(bootargs_root) rw initrd=0x02000040,20M panic=5 $(buffalo_ver); bootm $(default_kernel_addr) $(default_initrd_addr)
+
bootcmd=nboot $(default_kernel_addr) 0 $(nand_uImage_offset) ;setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver); bootm $(default_kernel_addr)
 +
def_tftp=tftp $(default_kernel_addr) $(kernel); tftp $(default_initrd_addr) $(initrd); setenv bootargs $(bootargs_base) $(bootargs_root) rw initrd=0x02000040,20M panic=5 $(buffalo_ver); bootm $(default_kernel_addr) $(default_initrd_addr)
nand_boot=yes
nand_boot=yes
-
stdin=serial
 
-
stdout=serial
 
-
stderr=serial
 
-
enaMonExt=no
 
-
enaFlashBuf=yes
 
-
enaCpuStream=no
 
-
ethprime=egiga0
 
bootdelay=3
bootdelay=3
disaMvPnp=no
disaMvPnp=no
Line 63: Line 65:
usb0Mode=host
usb0Mode=host
usb1Mode=host
usb1Mode=host
-
force_tftp=1
+
ethact=egiga0
-
bootcmd=tftp $(default_kernel_addr) $(kernel); tftp $(default_initrd_addr) $(initrd); setenv bootargs $(bootargs_base) $(bootargs_root)  rw initrd=0x02000040,20M panic=5 $(buffalo_ver); bootm $(default_kernel_addr) $(default_initrd_addr)
+
ethaddr=XX:XX:XX:XX:XX:XX</pre>
-
 
+
-
Environment size: 1192/4092 bytes
+
-
</pre>
+
==HARD DRIVE BOOT==
==HARD DRIVE BOOT==
Line 105: Line 104:
|-
|-
||Notes ||  
||Notes ||  
-
* /dev/sdal is formatted in ext2, and uImage.buffalo is stored.  
+
* /dev/sda1 is formatted in ext2, and uImage.buffalo is stored.  
|}
|}
====u-boot environment settings====
====u-boot environment settings====
Line 190: Line 189:
setenv serverip 192.168.11.100  
setenv serverip 192.168.11.100  
setenv ipaddr 192.168.11.150  
setenv ipaddr 192.168.11.150  
-
setenv bootcmd ‘tftp $(default_kernel_addr) $(kernel); bootm $(default_kernel_addr)
+
setenv bootcmd 'tftp $(default_kernel_addr) $(kernel); bootm $(default_kernel_addr)'
</pre>
</pre>
Line 219: Line 218:
setenv default_initrd_addr 0x02000000  
setenv default_initrd_addr 0x02000000  
setenv bootargs_base console=ttyS0,115200  
setenv bootargs_base console=ttyS0,115200  
-
setenv bootargs_root root=/dev/mtdblock2 rw  
+
setenv bootargs_root root=/dev/ram0 rw  
setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver)  
setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver)  
setenv serverip 192.168.11.100  
setenv serverip 192.168.11.100  
setenv ipaddr 192.168.11.150  
setenv ipaddr 192.168.11.150  
-
setenv bootcmd ‘tftp $(default_kernel_addr) $(kernel); tftp $(default_initrd_addr) $(initrd); bootm$(default_kernel_addr) $(default_initrd_addr)’
+
setenv bootcmd 'tftp $(default_kernel_addr) $(kernel); tftp $(default_initrd_addr) $(initrd); bootm $(default_kernel_addr) $(default_initrd_addr)'
</pre>
</pre>

Latest revision as of 14:11, 21 May 2008


Contents

CHANGING U-BOOT SETTINGS

use "setenv ... " as shown below, check with "printenv", then save to flash with "saveenv".

FLASH BOOT

Boot settings when uImage(nand /dev/mtdblock1), rootfs(nand /dev/mtdblock2)

uImage /dev/mtdblock1 (0x00020000~0x00400000)

4MB arrangement excluding head 128KB

initrd ----- (Not use)
rootfs /dev/mtdblock2

u-boot environment variable settings

setenv default_kernel_addr 0x00100000 
setenv bootargs_base console=ttyS0,115200 
setenv bootargs_root root=/dev/mtdblock2 rw 
setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) 
setenv uImage_block 0 
setenv uImage_offset 0x00020000 
setenv bootcmd 'nboot $(default_kernel_addr) $(uImage_block) $(uImage_offset); bootm $(default_kernel_addr)'

Marvell>> environment at the time of Flash starting

baudrate=115200
loads_echo=0
ipaddr=192.168.11.150
serverip=192.168.11.1
rootpath=/nfs/arm
stdin=serial
stdout=serial
stderr=serial
cpuName=926
CASset=min
enaMonExt=no
enaFlashBuf=yes
enaCpuStream=no
MALLOC_len=4
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
buffalo_ver=BOOTVER=1.091
build_time=18:10:02
initrd=initrd.buffalo
kernel=uImage.buffalo
bootargs_base=console=ttyS0,115200
bootargs_root=root=/dev/mtdblock2 rw panic=5
bootargs=$(bootargs_base) $(bootargs_root) $(buffalo_ver)
nand_uImage_offset=20000
default_kernel_addr=0x00100000
default_initrd_addr=0x02000000
bootcmd=nboot $(default_kernel_addr) 0 $(nand_uImage_offset) ;setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver); bootm $(default_kernel_addr)
def_tftp=tftp $(default_kernel_addr) $(kernel); tftp $(default_initrd_addr) $(initrd); setenv bootargs $(bootargs_base) $(bootargs_root) rw initrd=0x02000040,20M panic=5 $(buffalo_ver); bootm $(default_kernel_addr) $(default_initrd_addr)
nand_boot=yes
bootdelay=3
disaMvPnp=no
overEthAddr=no
usb0Mode=host
usb1Mode=host
ethact=egiga0
ethaddr=XX:XX:XX:XX:XX:XX

HARD DRIVE BOOT

Boot settings when uImage(nand /dev/mtdblock1), rootfs(/dev/sda2)

uImage /dev/mtdblock1 (0x00020000~0x00400000)

4MB arrangement excluding head 128KB

initrd -----(Not use)
rootfs /dev/sda2

u-boot environment settings

setenv default_kernel_addr 0x00100000 
setenv bootargs_base console=ttyS0,115200 
setenv bootargs_root root=/dev/sda2 rw 
setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) 
setenv uImage block 0 
setenv uImage_offset 0x00020000 
setenv bootcmd 'nboot $(default_kernel_addr) $(uImage_block) $(uImage_offset); bootm $(default_kernel_addr)'

Boot settings when uImage(/dev/sda1), rootfs(/dev/sda2)

uImage /dev/sda1
initrd -----(Not use)
rootfs /dev/sda2
Notes
  • /dev/sda1 is formatted in ext2, and uImage.buffalo is stored.

u-boot environment settings

setenv default_kernel_addr 0x00100000 
setenv bootargs_base console=ttyS0,115200 
setenv bootargs_root root=/dev/sda2 rw 
setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) 
setenv bootcmd 'ext2load ide 0:1 $(default_kernel_addr)/$(kernel); bootm $(default_kernel_addr)'

Marvell>> printenv At the time of HDD starting

baudrate=115200
loads_echo=0
ipaddr=192.168.11.150
serverip=192.168.11.1
rootpath=/nfs/arm
cpuName=926
CASset=min
MALLOC_len=4
bootargs_end=:::DB88FXX81:eth0:none
ethact=egiga0
ethaddr=00:16:01:A4:C2:4A
buffalo_ver=BOOTVER=1.091
build_time=15:59:38
initrd=initrd.buffalo
kernel=uImage.buffalo
bootargs_base=console=ttyS0,115200
bootargs_root=root=/dev/sda2 rw panic=5
bootargs=console=ttyS0,115200 root=/dev/sda2 rw panic=5 BOOTVER=1.09
nand_uImage_offset=20000
default_kernel_addr=0x00100000
default_initrd_addr=0x02000000
def_tftp=tftp $(default_kernel_addr) $(kernel); tftp $(default_initrd_addr) $(initrd); setenv bootargs $(bootargs_base) $(bootargs_root)  rw initrd=0x02000040,20M panic=5 $(buffalo_ver); bootm $(default_kernel_addr) $(default_initrd_addr)
nand_boot=no
stdin=serial
stdout=serial
stderr=serial
enaMonExt=no
enaFlashBuf=yes
enaCpuStream=no
ethprime=egiga0
bootdelay=3
disaMvPnp=no
overEthAddr=no
usb0Mode=host
usb1Mode=host
force_tftp=1
bootcmd=tftp $(default_kernel_addr) $(kernel); tftp $(default_initrd_addr) $(initrd); setenv bootargs $(bootargs_base) $(bootargs_root)  rw initrd=0x02000040,20M panic=5 $(buffalo_ver); bootm $(default_kernel_addr) $(default_initrd_addr)

Environment size: 1197/4092 bytes


TFTP BOOT

Boot settings when uImage(tftp load), rootfs(nand /dev/mtdblock2)

uImage Load from tftp
initrd -----(Not use)
rootfs /dev/mtdblock2
tftpserver (e.g.) 192.168.11.100
KUROBOX-PRO (e.g.) 192.168.11.150
Notes
  • uImage.buffalo exists in the tftp root directory of tftpserver.

u-boot environment variable settings

setenv default_kernel_addr 0x00100000 
setenv bootargs_base console=ttyS0,115200 
setenv bootargs_root root=/dev/mtdblock2 rw 
setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) 
setenv serverip 192.168.11.100 
setenv ipaddr 192.168.11.150 
setenv bootcmd 'tftp $(default_kernel_addr) $(kernel); bootm $(default_kernel_addr)'

Boot settings when uImage(tftp load), initrd(tftp load)

uImage Load from tftp
initrd Load from tftp
rootfs Exists in initrd
tftpserver (e.g.) 192.168.11.100
KUROBOX-PRO (e.g.) 192.168.11.150
Notes
  • uImage.buffalo and initrd.buffalo exist in the tftp root directory of tftpserver.
  • rootfs exists in initrd.
  • After expanding rootfs in initrd, it is within 32MB.

u-boot environment variable settings

setenv default_kernel_addr 0x00100000 
setenv default_initrd_addr 0x02000000 
setenv bootargs_base console=ttyS0,115200 
setenv bootargs_root root=/dev/ram0 rw 
setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver) 
setenv serverip 192.168.11.100 
setenv ipaddr 192.168.11.150 
setenv bootcmd 'tftp $(default_kernel_addr) $(kernel); tftp $(default_initrd_addr) $(initrd); bootm $(default_kernel_addr) $(default_initrd_addr)'
Retrieved from "http://buffalo.nas-central.org/wiki/Kurobox_Pro_u-boot_environment_variable_settings"
Personal tools