Difference between revisions of "LS DUO: Serial Port Output - Boot-Log"

From NAS-Central Buffalo - The Linkstation Wiki
Jump to: navigation, search
m (New page: =Serial Port Output= ==Bootup Sequence== > Checking hardware info ... === Strap status : 0x00002030 === === H/W boardId : 0x13 === === boardId : 0x18 === ...)
 
m (Reorder - compareable to http://buffalo.nas-central.org/wiki/LS_Mini:_Serial_Port_Output_-_U-Boot#Environment)
 
(5 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 +
{{Articles|Hardware|LS-WTGL/R1}}
 +
[[Image:LS-WTGL-R1.jpg|100px|thumb|right]]
 
=Serial Port Output=
 
=Serial Port Output=
 +
This information comes from this forum thread [http://buffalo.nas-central.org/forums/viewtopic.php?f=50&t=5871 The Buffalo NAS hacking Forums:Serial @ Pro Duo]
 +
==U-Boot Version==
 +
<pre>Marvell>> version
 +
 +
U-Boot 1.1.1 (Jan  7 2008 - 21:04:08) Marvell version: 1.12.1 - TINY</pre>
 +
==Possible u-boot commands==
 +
 +
    Marvell>> help
 +
    ?      - alias for 'help'
 +
    base    - print or set address offset
 +
    board_info  -show board information.
 +
    boot    - boot default, i.e., run 'bootcmd'
 +
    bootd  - boot default, i.e., run 'bootcmd'
 +
    bootend - with micon. send bootend.
 +
    bootm  - boot application image from memory
 +
    bootp  - boot image via network using BootP/TFTP protocol
 +
    bubt    - Burn an image on the Boot Flash.
 +
    buzzer          - with micon. buzzer command.
 +
    cmp    - memory compare
 +
    cp      - memory copy
 +
    cpumap - Display CPU memory mapping settings.
 +
    crc32  - checksum calculation
 +
    date    - get/set/reset date & time
 +
    diskboot- boot from IDE device
 +
    echo    - echo args to console
 +
    erase  - erase FLASH memory
 +
    ext2load- load binary file from a Ext2 filesystem
 +
    ext2ls- list files in a directory (default /)
 +
    fan_control    - with micon. fan control  .
 +
    fan_rpm        - with micon. fan get rpm.
 +
    flinfo  - print FLASH memory information
 +
    get_sw          - without micon. get switch status.
 +
    go      - start application at address 'addr'
 +
    hdd_power      - hdd power control  .
 +
    help    - print online help
 +
    ide    - IDE sub-system
 +
    led            - without micon. call led control routine(for debug).
 +
    led_blink      - with micon. led blink control setting.
 +
    led_cpu_mcon    - with micon. led cpu micon control setting.
 +
    led_on_off      - with micon. led on off control setting.
 +
    loop    - infinite loop on address range
 +
    md      - memory display
 +
    micon          - with micon. command(2byte hex) -data(witin 32byte hex)
 +
    mm      - memory modify (auto-incrementing)
 +
    mtest  - simple RAM test
 +
    mw      - memory write (fill)
 +
    nm      - memory modify (constant address)
 +
    pci    - list and access PCI Configuraton Space
 +
    printenv- print environment variables
 +
    protect - enable or disable FLASH write protection
 +
    rarpboot- boot image via network using RARP/TFTP protocol
 +
    reset  - Perform RESET of the CPU
 +
    resetenv        - Return all environment variable to default.
 +
    saveenv - save environment variables to persistent storage
 +
    security -device -command -options -password
 +
    setenv  - set environment variables
 +
    shutdown        - with micon. Poff .
 +
    sw_power        - with micon. software power control interface
 +
    tftpboot- boot image via network using TFTP protocol
 +
    usb_power      - without micon. usb power control  .
 +
    version - print monitor version
 +
==Flash Information==
 +
<pre>Marvell>> flinfo
 +
 +
Bank # 1: SST SST39VF020 (2 Mbit)
 +
Size: 256 kB,Bus Width: 1, device Width: 1.
 +
Flash base: 0xfffc0000,Number of Sectors: 64 Type: REGULAR.
 +
  Sector Start Addresses:
 +
    00000000 (RO) 00001000 (RO) 00002000 (RO) 00003000 (RO) 00004000 (RO)
 +
    00005000 (RO) 00006000 (RO) 00007000 (RO) 00008000 (RO) 00009000 (RO)
 +
    0000a000 (RO) 0000b000 (RO) 0000c000 (RO) 0000d000 (RO) 0000e000 (RO)
 +
    0000f000 (RO) 00010000 (RO) 00011000 (RO) 00012000 (RO) 00013000 (RO)
 +
    00014000 (RO) 00015000 (RO) 00016000 (RO) 00017000 (RO) 00018000 (RO)
 +
    00019000 (RO) 0001a000 (RO) 0001b000 (RO) 0001c000 (RO) 0001d000 (RO)
 +
    0001e000 (RO) 0001f000 (RO) 00020000 (RO) 00021000 (RO) 00022000 (RO)
 +
    00023000 (RO) 00024000 (RO) 00025000 (RO) 00026000 (RO) 00027000 (RO)
 +
    00028000 (RO) 00029000 (RO) 0002a000 (RO) 0002b000 (RO) 0002c000 (RO)
 +
    0002d000 (RO) 0002e000 (RO) 0002f000 (RO) 00030000 (RO) 00031000 (RO)
 +
    00032000 (RO) 00033000 (RO) 00034000 (RO) 00035000 (RO) 00036000 (RO)
 +
    00037000 (RO) 00038000 (RO) 00039000 (RO) 0003a000 (RO) 0003b000 (RO)
 +
    0003c000 (RO) 0003d000 (RO) 0003e000 (RO) 0003f000
 +
 +
Bank # 2: missing or unknown FLASH type</pre>
 +
==Board Information==
 +
<pre>Marvell>> board_info
 +
board configuration
 +
        VGPP_CONFIG_NUM=  2
 +
        BoardId        =  24    (0x0018)
 +
        gBoardId      =  24    (0x0018)
 +
 +
power control bit
 +
        hdd_power      =  1    (0x0002)
 +
        usb_power      =  9    (0x0200)
 +
 +
led control bit
 +
        led_info      =  3    (0x0008)
 +
        led_power      =  0    (0x0001)
 +
        led_alarm      =  2    (0x0004)
 +
 +
fan control bit
 +
        fan_full      =  14    (0x4000)
 +
        fan_lock      =  6    (0x0040)
 +
 +
sw control bit
 +
        sw_init        =  7    (0x0080)
 +
        sw_power      =  8    (0x0100)
 +
        sw_raid        = 255    (0x0000)
 +
        sw_auto_power  =  10    (0x0400)</pre>
 +
==Switch status==
 +
<pre>Marvell>> get_sw
 +
Usage:
 +
get_sw          - without micon. get switch status.
 +
 +
sw_status = 0x0001</pre>
 +
==PCI Configuration==
 +
<pre>Marvell>> pci
 +
Scanning PCI devices on bus 0
 +
BusDevFun  VendorId  DeviceId  Device Class      Sub-Class
 +
_____________________________________________________________
 +
00.00.00  0x11ab    0x5182    Memory controller      0x80
 +
</pre>
 
==Bootup Sequence==
 
==Bootup Sequence==
 +
<pre>
 
     > Checking hardware info ...
 
     > Checking hardware info ...
 
     === Strap status : 0x00002030 ===
 
     === Strap status : 0x00002030 ===
Line 39: Line 163:
  
 
     Please Press HDD power button to continue ...
 
     Please Press HDD power button to continue ...
 +
</pre>
  
 
==RunLevel 2==
 
==RunLevel 2==
Code: Select all
+
<pre>
 
     buffalo_change_power_status > Read 0x5c
 
     buffalo_change_power_status > Read 0x5c
 
     buffalo_change_power_status > Writing 0x3a
 
     buffalo_change_power_status > Writing 0x3a
Line 389: Line 514:
 
     INIT: Entering runlevel: 2
 
     INIT: Entering runlevel: 2
 
     err: RecvPacket: readlen=0.
 
     err: RecvPacket: readlen=0.
 
+
</pre>
==Possible u-boot commands==
+
 
+
    Marvell>> help
+
    ?      - alias for 'help'
+
    base    - print or set address offset
+
    board_info  -show board information.
+
    boot    - boot default, i.e., run 'bootcmd'
+
    bootd  - boot default, i.e., run 'bootcmd'
+
    bootend - with micon. send bootend.
+
    bootm  - boot application image from memory
+
    bootp  - boot image via network using BootP/TFTP protocol
+
    bubt    - Burn an image on the Boot Flash.
+
    buzzer          - with micon. buzzer command.
+
    cmp    - memory compare
+
    cp      - memory copy
+
    cpumap - Display CPU memory mapping settings.
+
    crc32  - checksum calculation
+
    date    - get/set/reset date & time
+
    diskboot- boot from IDE device
+
    echo    - echo args to console
+
    erase  - erase FLASH memory
+
    ext2load- load binary file from a Ext2 filesystem
+
    ext2ls- list files in a directory (default /)
+
    fan_control    - with micon. fan control  .
+
    fan_rpm        - with micon. fan get rpm.
+
    flinfo  - print FLASH memory information
+
    get_sw          - without micon. get switch status.
+
    go      - start application at address 'addr'
+
    hdd_power      - hdd power control  .
+
    help    - print online help
+
    ide    - IDE sub-system
+
    led            - without micon. call led control routine(for debug).
+
    led_blink      - with micon. led blink control setting.
+
    led_cpu_mcon    - with micon. led cpu micon control setting.
+
    led_on_off      - with micon. led on off control setting.
+
    loop    - infinite loop on address range
+
    md      - memory display
+
    micon          - with micon. command(2byte hex) -data(witin 32byte hex)
+
    mm      - memory modify (auto-incrementing)
+
    mtest  - simple RAM test
+
    mw      - memory write (fill)
+
    nm      - memory modify (constant address)
+
    pci    - list and access PCI Configuraton Space
+
    printenv- print environment variables
+
    protect - enable or disable FLASH write protection
+
    rarpboot- boot image via network using RARP/TFTP protocol
+
    reset  - Perform RESET of the CPU
+
    resetenv        - Return all environment variable to default.
+
    saveenv - save environment variables to persistent storage
+
    security -device -command -options -password
+
    setenv  - set environment variables
+
    shutdown        - with micon. Poff .
+
    sw_power        - with micon. software power control interface
+
    tftpboot- boot image via network using TFTP protocol
+
    usb_power      - without micon. usb power control  .
+
    version - print monitor version
+

Latest revision as of 18:58, 15 June 2009

LS-WTGL-R1.jpg

Contents

Serial Port Output

This information comes from this forum thread The Buffalo NAS hacking Forums:Serial @ Pro Duo

U-Boot Version

Marvell>> version

U-Boot 1.1.1 (Jan  7 2008 - 21:04:08) Marvell version: 1.12.1 - TINY

Possible u-boot commands

   Marvell>> help
   ?       - alias for 'help'
   base    - print or set address offset
   board_info   -show board information.
   boot    - boot default, i.e., run 'bootcmd'
   bootd   - boot default, i.e., run 'bootcmd'
   bootend - with micon. send bootend.
   bootm   - boot application image from memory
   bootp   - boot image via network using BootP/TFTP protocol
   bubt    - Burn an image on the Boot Flash.
   buzzer          - with micon. buzzer command.
   cmp     - memory compare
   cp      - memory copy
   cpumap - Display CPU memory mapping settings.
   crc32   - checksum calculation
   date    - get/set/reset date & time
   diskboot- boot from IDE device
   echo    - echo args to console
   erase   - erase FLASH memory
   ext2load- load binary file from a Ext2 filesystem
   ext2ls- list files in a directory (default /)
   fan_control     - with micon. fan control  .
   fan_rpm         - with micon. fan get rpm.
   flinfo  - print FLASH memory information
   get_sw          - without micon. get switch status.
   go      - start application at address 'addr'
   hdd_power       - hdd power control  .
   help    - print online help
   ide     - IDE sub-system
   led             - without micon. call led control routine(for debug).
   led_blink       - with micon. led blink control setting.
   led_cpu_mcon    - with micon. led cpu micon control setting.
   led_on_off      - with micon. led on off control setting.
   loop    - infinite loop on address range
   md      - memory display
   micon           - with micon. command(2byte hex) -data(witin 32byte hex)
   mm      - memory modify (auto-incrementing)
   mtest   - simple RAM test
   mw      - memory write (fill)
   nm      - memory modify (constant address)
   pci     - list and access PCI Configuraton Space
   printenv- print environment variables
   protect - enable or disable FLASH write protection
   rarpboot- boot image via network using RARP/TFTP protocol
   reset   - Perform RESET of the CPU
   resetenv        - Return all environment variable to default.
   saveenv - save environment variables to persistent storage
   security -device -command -options -password
   setenv  - set environment variables
   shutdown        - with micon. Poff .
   sw_power        - with micon. software power control interface
   tftpboot- boot image via network using TFTP protocol
   usb_power       - without micon. usb power control  .
   version - print monitor version

Flash Information

Marvell>> flinfo

Bank # 1: SST SST39VF020 (2 Mbit)
Size: 256 kB,Bus Width: 1, device Width: 1.
Flash base: 0xfffc0000,Number of Sectors: 64 Type: REGULAR.
  Sector Start Addresses:
    00000000 (RO) 00001000 (RO) 00002000 (RO) 00003000 (RO) 00004000 (RO)
    00005000 (RO) 00006000 (RO) 00007000 (RO) 00008000 (RO) 00009000 (RO)
    0000a000 (RO) 0000b000 (RO) 0000c000 (RO) 0000d000 (RO) 0000e000 (RO)
    0000f000 (RO) 00010000 (RO) 00011000 (RO) 00012000 (RO) 00013000 (RO)
    00014000 (RO) 00015000 (RO) 00016000 (RO) 00017000 (RO) 00018000 (RO)
    00019000 (RO) 0001a000 (RO) 0001b000 (RO) 0001c000 (RO) 0001d000 (RO)
    0001e000 (RO) 0001f000 (RO) 00020000 (RO) 00021000 (RO) 00022000 (RO)
    00023000 (RO) 00024000 (RO) 00025000 (RO) 00026000 (RO) 00027000 (RO)
    00028000 (RO) 00029000 (RO) 0002a000 (RO) 0002b000 (RO) 0002c000 (RO)
    0002d000 (RO) 0002e000 (RO) 0002f000 (RO) 00030000 (RO) 00031000 (RO)
    00032000 (RO) 00033000 (RO) 00034000 (RO) 00035000 (RO) 00036000 (RO)
    00037000 (RO) 00038000 (RO) 00039000 (RO) 0003a000 (RO) 0003b000 (RO)
    0003c000 (RO) 0003d000 (RO) 0003e000 (RO) 0003f000

Bank # 2: missing or unknown FLASH type

Board Information

Marvell>> board_info
board configuration
        VGPP_CONFIG_NUM=   2
        BoardId        =  24    (0x0018)
        gBoardId       =  24    (0x0018)

power control bit
        hdd_power      =   1    (0x0002)
        usb_power      =   9    (0x0200)

led control bit
        led_info       =   3    (0x0008)
        led_power      =   0    (0x0001)
        led_alarm      =   2    (0x0004)

fan control bit
        fan_full       =  14    (0x4000)
        fan_lock       =   6    (0x0040)

sw control bit
        sw_init        =   7    (0x0080)
        sw_power       =   8    (0x0100)
        sw_raid        = 255    (0x0000)
        sw_auto_power  =  10    (0x0400)

Switch status

Marvell>> get_sw
Usage:
get_sw          - without micon. get switch status.

sw_status = 0x0001

PCI Configuration

Marvell>> pci
Scanning PCI devices on bus 0
BusDevFun  VendorId   DeviceId   Device Class       Sub-Class
_____________________________________________________________
00.00.00   0x11ab     0x5182     Memory controller       0x80

Bootup Sequence

    > Checking hardware info ...
    === Strap status : 0x00002030 ===
    === H/W boardId  :       0x13 ===
    === boardId      :       0x18 ===
    === micon_support:        off ===
    > OK.
    === BUFFALO LS-WTGL/R1 U-Boot. ===
    ** LOADER **
    ** BUFFALO BOARD: BUFFALO_BOARD_LS_WTGL/R1 LE (CFG_ENV_ADDR=fffff000)


    U-Boot 1.1.1 (Jan  7 2008 - 21:04:08) Marvell version: 1.12.1 - TINY
    Buffalo Version: 1.13-1.00

    DRAM CS[0] base 0x00000000   size  64MB
    DRAM Total size  64MB
    [256kB@fffc0000] Flash: 256 kB
    Addresses 20M - 0M are saved for the U-Boot usage.
    Mem malloc Initialization (20M - 16M): Done

    Soc: 88F5182 A2
    CPU: ARM926 (Rev 0) running @ 400Mhz
    Orion 1 streaming disabled
    SysClock = 250Mhz , TClock = 166Mhz


    USB 0: host mode
    PCI 0: PCI Express Root Complex Interface
    PCI 1: Conventional PCI, speed = 33000000
    Net:   egiga0 [PRIME]
    Using 88E1118 phy
    buffalo_change_power_status > Read 0x3a
    buffalo_IsStopAtUbootStatus > MagicKey=0x3a
    buffalo_change_power_status > Read 0x3a
    buffalo_change_power_status > Read 0x3a
    buffalo_change_power_status > Writing 0x5c

    Please Press HDD power button to continue ...

RunLevel 2

    buffalo_change_power_status > Read 0x5c
    buffalo_change_power_status > Writing 0x3a

    Marvell Serial ATA Adapter
    Integrated Sata device found
      Device 0: OK
    Model: SAMSUNG HD501LJ                          Firm: CR100-10 Ser#: S0MUJDSP620337
                Type: Hard Disk
                Supports 48-bit addressing
                Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
      Device 1: OK
    Model: SAMSUNG HD501LJ                          Firm: CR100-12 Ser#: S0Z4J1FP804864
                Type: Hard Disk
                Supports 48-bit addressing
                Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)

    Using device ide0, partition 1

    Loading from block device ide device 0, partition 1: Name: hda1
      Type: U-Boot  File:/initrd.buffalo

    4563579 bytes read
    Using device ide1, partition 1

    Loading from block device ide device 1, partition 1: Name: hdb1
      Type: U-Boot  File:/initrd.buffalo

    4563579 bytes read
    Booting from Device 0
    hit any key to switch tftp boot.
    Hit any key to stop autoboot:  0
    Hit any key to stop autoboot:  0

    Reset IDE:
    Marvell Serial ATA Adapter
    Integrated Sata device found
      Device 0: OK
    Model: SAMSUNG HD501LJ                          Firm: CR100-10 Ser#: S0MUJDSP620337
                Type: Hard Disk
                Supports 48-bit addressing
                Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
      Device 1: OK
    Model: SAMSUNG HD501LJ                          Firm: CR100-12 Ser#: S0Z4J1FP804864
                Type: Hard Disk
                Supports 48-bit addressing
                Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)

    Using device ide0, partition 1

    Loading from block device ide device 0, partition 1: Name: hda1
      Type: U-Boot  File:/uImage.buffalo

    1949476 bytes read
    Using device ide1, partition 1

    Loading from block device ide device 1, partition 1: Name: hdb1
      Type: U-Boot  File:/initrd.buffalo

    4563579 bytes read
    ## Booting image at 00100000 ...
       Image Name:   Linux-2.6.16.16-teralive110gpl4L
       Created:      2007-11-03  22:18:47 UTC
       Image Type:   ARM Linux Kernel Image (uncompressed)
       Data Size:    1949412 Bytes =  1.9 MB
       Load Address: 00008000
       Entry Point:  00008000
       Verifying Checksum ... OK
    OK
    ## Loading Ramdisk Image at 00800000 ...
       Image Name:   initrd
       Created:      2006-12-27  21:19:31 UTC
       Image Type:   ARM Linux RAMDisk Image (gzip compressed)
       Data Size:    4563515 Bytes =  4.4 MB
       Load Address: 00000000
       Entry Point:  00000000
       Verifying Checksum ... OK

    Starting kernel ...

    arg:console=ttyS0,115200 mem=64m root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.13
    CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSGL ---
    Uncompressing Linux...........................................................................................
    Linux version 2.6.16.16-teralive110gpl4LSPro-mb_v6 (mindbender@mindbender) (gcc version 3.4.4 (release) (Code7
    CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
    Machine: MV-88fxx81
    Using UBoot passing parameters structure
    Sys Clk = 250000000, Tclk = 166664740


    - Warning - This LSP release was tested only with U-Boot release 1.7.3

    Memory policy: ECC disabled, Data cache writeback
    CPU0: D VIVT write-back cache
    CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
    CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
    Built 1 zonelists
    Kernel command line: console=ttyS0,115200 mem=64m root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.13
    PID hash table entries: 512 (order: 9, 8192 bytes)
    Console: colour dummy device 80x30
    Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
    Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
    Memory: 64MB = 64MB total
    Memory: 45384KB available (3340K code, 596K data, 116K init)
    Mount-cache hash table entries: 512
    CPU: Testing write buffer coherency: ok
    checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
    Freeing initrd memory: 15360K
    NET: Registered protocol family 16
    FLASH boardId = 12
    Flash bankwidth 1, base ff800000, size 400000
    BUFFALO LS_GL FLASH size 4096[KB]

      Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_GL

    Detected Tclk 166664740 and SysClk 250000000
    Marvell USB EHCI Host controller #0: c16f5e00
    Marvell USB EHCI Host controller #1: c16f5c00
    pexBarOverlapDetect: winNum 2 overlap current 0
    mvPexInit:Warning :Bar 2 size is illigal
    it will be disabled
    please check Pex and CPU windows configuration
    Request resource failed - PEX 0
    PCI: bus0: Fast back to back transfers enabled
    PCI: bus1: Fast back to back transfers enabled
    SCSI subsystem initialized
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
    Done.
    cesadev_init(c0011b74)
    Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
    SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
    SGI XFS Quota Management subsystem
    Initializing Cryptographic API
    io scheduler noop registered
    io scheduler anticipatory registered (default)
    io scheduler deadline registered
    io scheduler cfq registered
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
    serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
    serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
    RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
    loop: loaded (max 8 devices)
    Marvell Gigabit Ethernet Driver 'egiga':
      o Ethernet descriptors in DRAM
      o DRAM SW cache-coherency
      o Checksum offload enabled
      o Loading network interface ** egiga_init_module (0)
    'eth0'
    Intergrated Sata device found
    scsi0 : Marvell SCSI to SATA adapter
    scsi1 : Marvell SCSI to SATA adapter
    ** BUFFALO Disable Command Queuing Function [0 0] **
    ** BUFFALO Disable Command Queuing Function [0 1] **
      Vendor: SAMSUNG   Model: HD501LJ           Rev: CR10
      Type:   Direct-Access                      ANSI SCSI revision: 03
      Vendor: SAMSUNG   Model: HD501LJ           Rev: CR10
      Type:   Direct-Access                      ANSI SCSI revision: 03
    Linux IAL (ERROR) : retry command host=0, bus=0 SCpnt = c37bbba0
    SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
    sda: Write Protect is off
    SCSI device sda: drive cache: write back
    SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
    sda: Write Protect is off
    SCSI device sda: drive cache: write back
    sda: sda1 sda2 sda4 < sda5 sda6 >
    sd 0:0:0:0: Attached scsi disk sda
    Linux IAL (ERROR) : retry command host=1, bus=1 SCpnt = c37bbba0
    SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
    sdb: Write Protect is off
    SCSI device sdb: drive cache: write back
    SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
    sdb: Write Protect is off
    SCSI device sdb: drive cache: write back
    sdb: sdb1 sdb2 sdb4 < sdb5 sdb6 >
    sd 1:0:0:0: Attached scsi disk sdb
    sd 0:0:0:0: Attached scsi generic sg0 type 0
    sd 1:0:0:0: Attached scsi generic sg1 type 0
    physmap flash device: 400000 at ff800000
    >jedec_probe
    Found: SST 39LF020
    phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
    number of JEDEC chips: 1
    cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
    cmdlinepart partition parsing not available
    RedBoot partition parsing not available
    ehci_platform ehci_platform.4523: EHCI Platform Host Controller
    ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
    ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
    ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb1: Product: EHCI Platform Host Controller
    usb usb1: Manufacturer: Linux 2.6.16.16-teralive110gpl4LSPro-mb_v6 ehci_hcd
    usb usb1: SerialNumber: ehci_platform.4523
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 1 port detected
    ehci_platform ehci_platform.16781: EHCI Platform Host Controller
    ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
    ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
    ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb2: Product: EHCI Platform Host Controller
    usb usb2: Manufacturer: Linux 2.6.16.16-teralive110gpl4LSPro-mb_v6 ehci_hcd
    usb usb2: SerialNumber: ehci_platform.16781
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 1 port detected
    USB Universal Host Controller Interface driver v2.3
    usbcore: registered new driver usblp
    drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
    Initializing USB Mass Storage driver...
    usbcore: registered new driver usb-storage
    USB Mass Storage support registered.
    mice: PS/2 mouse device common for all mice
    md: linear personality registered for level -1
    md: raid0 personality registered for level 0
    md: raid1 personality registered for level 1
    md: raid5 personality registered for level 5
    md: raid4 personality registered for level 4
    raid5: measuring checksumming speed
       arm4regs  :   308.800 MB/sec
       8regs     :   217.600 MB/sec
       32regs    :   252.400 MB/sec
    raid5: using function: arm4regs (308.800 MB/sec)
    md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
    md: bitmap version 4.39
    Kernel event proc (C) BUFFALO INC. V.1.00 installed.
    MICON ctrl (C) BUFFALO INC. V.1.00 installed.
    MICON V2 (C) BUFFALO INC. V.1.00 installed.
    NET: Registered protocol family 2
    IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
    TCP established hash table entries: 4096 (order: 2, 16384 bytes)
    TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
    TCP: Hash tables configured (established 4096 bind 4096)
    TCP reno registered
    TCP bic registered
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    md: Autodetecting RAID arrays.
    md: autorun ...
    md: considering sdb6 ...
    md:  adding sdb6 ...
    md:  adding sda6 ...
    md: created md2
    md: bind<sda6>
    md: bind<sdb6>
    md: running: <sdb6><sda6>
    raid1: raid set md2 active with 2 out of 2 mirrors
    md: ... autorun DONE.
    RAMDISK: Compressed image found at block 0
    EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
    VFS: Mounted root (ext2 filesystem).
    ---- in Modified linuxrc ---
    Thu Mar 20 20:17:05 JST 2008
    err: RecvPacket: readlen=0.
    kjournald starting.  Commit interval 5 seconds
    EXT3 FS on sda1, internal journal
    EXT3-fs: recovery complete.
    EXT3-fs: mounted filesystem with ordered data mode.
    err: RecvPacket: readlen=0.
    err: RecvPacket: readlen=0.
    err: RecvPacket: readlen=0.
    err: RecvPacket: readlen=0.
    linuxrc:choose operation (timeout 4[s])
    1:RamRoot other:HddRoot  ? -HddRoot-
    KERNEL:2007/11/3 23:17:32
    HDD:2007/6/28 9:42:0
    >>> Not expected kernel version, upgrade /etc/linkstation_release
    Bypassing CopyFromInitrdToHdd
    checking local disk....
    fsck 1.27 (8-Mar-2002)
    e2fsck 1.27 (8-Mar-2002)
    fsck.ext2: Filesystem has unsupported feature(s) (/dev/ls_disk1_1)
    e2fsck: Get a newer version of e2fsck!
    done
    XFS mounting filesystem sda2
    Starting XFS recovery on filesystem: sda2 (logdev: internal)
    Ending XFS recovery on filesystem: sda2 (logdev: internal)
    VFS: Mounted root (xfs filesystem).
    Trying to move old root to /initrd ... okay
    Freeing init memory: 116K
    INIT: version 2.86 booting
    * .udev/ already exists on the static /dev!
    Starting the hotplug events dispatcher: udevdudevd[357]: main: the kernel does not support inotify, udevd cans
    .
    Synthesizing the initial hotplug events...SAL (ERROR)  0 0 0 :Scsi command completed. pScb c37162c0, ScsiStatD
    SAL (ERROR) CDB:12 1 0 0 fe 0
    SAL (ERROR) Sense Data:70 0 5 0 0 0 0 a 0 0 0 0 24 0 0 0 0 0
    SAL (ERROR)  0 1 0 :Scsi command completed. pScb c37162c0, ScsiStatus 2 completionStatus MV_SCSI_COMPLETION_BD
    SAL (ERROR) CDB:12 1 0 0 fe 0
    SAL (ERROR) Sense Data:70 0 5 0 0 0 0 a 0 0 0 0 24 0 0 0 0 0
    SAL (ERROR)  0 0 0 :Scsi command completed. pScb c37162c0, ScsiStatus 2 completionStatus MV_SCSI_COMPLETION_BD
    SAL (ERROR) CDB:12 1 0 0 fe 0
    SAL (ERROR) Sense Data:70 0 5 0 0 0 0 a 0 0 0 0 24 0 0 0 0 0
    SAL (ERROR)  0 1 0 :Scsi command completed. pScb c37162c0, ScsiStatus 2 completionStatus MV_SCSI_COMPLETION_BD
    SAL (ERROR) CDB:12 1 0 0 fe 0
    SAL (ERROR) Sense Data:70 0 5 0 0 0 0 a 0 0 0 0 24 0 0 0 0 0
    done.
    Waiting for /dev to be fully populated...done.
    GSetting parameters of disc: (none).
    Activating swap:swapon on /dev/sda5
    Adding 1004020k swap on /dev/sda5.  Priority:-1 extents:1 across:1004020k
    swapon on /dev/sdb5
    Adding 1003896k swap on /dev/sdb5.  Priority:-2 extents:1 across:1003896k
    .
    Setting the system clock..
    System Clock set. Local time: Thu Mar 20 20:17:52 UTC 2008.
    Cleaning up ifupdown....
    Loading device-mapper support.
    Generating udev events for MD arrays...done.
    Will now check all file systems.
    fsck 1.40-WIP (14-Nov-2006)
    Checking all file systems.
    [/sbin/fsck.ext3 (1) -- /boot] fsck.ext3 -y -C0 /dev/sda1
    e2fsck 1.40-WIP (14-Nov-2006)
    /dev/sda1: clean, 22/125696 files, 11344/251007 blocks
    Done checking file systems.
    A log is being saved in /var/log/fsck/checkfs if that location is writable.
    Setting kernel variables...done.
    Will now mount local filesystems:mount: none already mounted or /dev/pts busy
    mount: according to mtab, devpts is already mounted on /dev/pts
    kjournald starting.  Commit interval 5 seconds
    EXT3 FS on sda1, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    EXT3-fs: journalled quota options not supported.
    EXT3-fs: journalled quota options not supported.
    kjournald starting.  Commit interval 5 seconds
    EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
    EXT3 FS on md2, internal journal
    EXT3-fs: recovery complete.
    EXT3-fs: mounted filesystem with ordered data mode.
    failed!
    Will now activate swapfile swap:done.
    Cleaning /var/run...done.
    Cleaning /var/lock...done.
    Setting up resolvconf...done.
    Setting up networking....
    * /etc/network/options is deprecated (see README.Debian of netbase).
    Setting up IP spoofing protection...done (rp_filter).
    Configuring network interfaces...eth0: link down
    done.
    Start services: micro_evtd
    Starting portmap daemon....
    eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
    Setting console screen modes and fonts.
    Starting kernelmon:Initializing random number generator...done.
    INIT: Entering runlevel: 2
    err: RecvPacket: readlen=0.