LS DUO: Serial Port Output - Boot-Log

From NAS-Central Buffalo - The Linkstation Wiki
Revision as of 04:50, 8 September 2008 by Ramuk (Talk | contribs)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

Contents

Serial Port Output

Bootup Sequence

   > Checking hardware info ...
   === Strap status : 0x00002030 ===
   === H/W boardId  :       0x13 ===
   === boardId      :       0x18 ===
   === micon_support:        off ===
   > OK.
   === BUFFALO LS-WTGL/R1 U-Boot. ===
   ** LOADER **
   ** BUFFALO BOARD: BUFFALO_BOARD_LS_WTGL/R1 LE (CFG_ENV_ADDR=fffff000)


   U-Boot 1.1.1 (Jan  7 2008 - 21:04:08) Marvell version: 1.12.1 - TINY
   Buffalo Version: 1.13-1.00
   DRAM CS[0] base 0x00000000   size  64MB
   DRAM Total size  64MB
   [256kB@fffc0000] Flash: 256 kB
   Addresses 20M - 0M are saved for the U-Boot usage.
   Mem malloc Initialization (20M - 16M): Done
   Soc: 88F5182 A2
   CPU: ARM926 (Rev 0) running @ 400Mhz
   Orion 1 streaming disabled
   SysClock = 250Mhz , TClock = 166Mhz


   USB 0: host mode
   PCI 0: PCI Express Root Complex Interface
   PCI 1: Conventional PCI, speed = 33000000
   Net:   egiga0 [PRIME]
   Using 88E1118 phy
   buffalo_change_power_status > Read 0x3a
   buffalo_IsStopAtUbootStatus > MagicKey=0x3a
   buffalo_change_power_status > Read 0x3a
   buffalo_change_power_status > Read 0x3a
   buffalo_change_power_status > Writing 0x5c
   Please Press HDD power button to continue ...

RunLevel 2

Code: Select all

   buffalo_change_power_status > Read 0x5c
   buffalo_change_power_status > Writing 0x3a
   Marvell Serial ATA Adapter
   Integrated Sata device found
     Device 0: OK
   Model: SAMSUNG HD501LJ                          Firm: CR100-10 Ser#: S0MUJDSP620337
               Type: Hard Disk
               Supports 48-bit addressing
               Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
     Device 1: OK
   Model: SAMSUNG HD501LJ                          Firm: CR100-12 Ser#: S0Z4J1FP804864
               Type: Hard Disk
               Supports 48-bit addressing
               Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
   Using device ide0, partition 1
   Loading from block device ide device 0, partition 1: Name: hda1
     Type: U-Boot  File:/initrd.buffalo
   4563579 bytes read
   Using device ide1, partition 1
   Loading from block device ide device 1, partition 1: Name: hdb1
     Type: U-Boot  File:/initrd.buffalo
   4563579 bytes read
   Booting from Device 0
   hit any key to switch tftp boot.
   Hit any key to stop autoboot:  0
   Hit any key to stop autoboot:  0
   Reset IDE:
   Marvell Serial ATA Adapter
   Integrated Sata device found
     Device 0: OK
   Model: SAMSUNG HD501LJ                          Firm: CR100-10 Ser#: S0MUJDSP620337
               Type: Hard Disk
               Supports 48-bit addressing
               Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
     Device 1: OK
   Model: SAMSUNG HD501LJ                          Firm: CR100-12 Ser#: S0Z4J1FP804864
               Type: Hard Disk
               Supports 48-bit addressing
               Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
   Using device ide0, partition 1
   Loading from block device ide device 0, partition 1: Name: hda1
     Type: U-Boot  File:/uImage.buffalo
   1949476 bytes read
   Using device ide1, partition 1
   Loading from block device ide device 1, partition 1: Name: hdb1
     Type: U-Boot  File:/initrd.buffalo
   4563579 bytes read
   ## Booting image at 00100000 ...
      Image Name:   Linux-2.6.16.16-teralive110gpl4L
      Created:      2007-11-03  22:18:47 UTC
      Image Type:   ARM Linux Kernel Image (uncompressed)
      Data Size:    1949412 Bytes =  1.9 MB
      Load Address: 00008000
      Entry Point:  00008000
      Verifying Checksum ... OK
   OK
   ## Loading Ramdisk Image at 00800000 ...
      Image Name:   initrd
      Created:      2006-12-27  21:19:31 UTC
      Image Type:   ARM Linux RAMDisk Image (gzip compressed)
      Data Size:    4563515 Bytes =  4.4 MB
      Load Address: 00000000
      Entry Point:  00000000
      Verifying Checksum ... OK
   Starting kernel ...
   arg:console=ttyS0,115200 mem=64m root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.13
   CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSGL ---
   Uncompressing Linux...........................................................................................
   Linux version 2.6.16.16-teralive110gpl4LSPro-mb_v6 (mindbender@mindbender) (gcc version 3.4.4 (release) (Code7
   CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
   Machine: MV-88fxx81
   Using UBoot passing parameters structure
   Sys Clk = 250000000, Tclk = 166664740


   - Warning - This LSP release was tested only with U-Boot release 1.7.3
   Memory policy: ECC disabled, Data cache writeback
   CPU0: D VIVT write-back cache
   CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
   CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
   Built 1 zonelists
   Kernel command line: console=ttyS0,115200 mem=64m root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.13
   PID hash table entries: 512 (order: 9, 8192 bytes)
   Console: colour dummy device 80x30
   Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
   Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
   Memory: 64MB = 64MB total
   Memory: 45384KB available (3340K code, 596K data, 116K init)
   Mount-cache hash table entries: 512
   CPU: Testing write buffer coherency: ok
   checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
   Freeing initrd memory: 15360K
   NET: Registered protocol family 16
   FLASH boardId = 12
   Flash bankwidth 1, base ff800000, size 400000
   BUFFALO LS_GL FLASH size 4096[KB]
     Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_GL
   Detected Tclk 166664740 and SysClk 250000000
   Marvell USB EHCI Host controller #0: c16f5e00
   Marvell USB EHCI Host controller #1: c16f5c00
   pexBarOverlapDetect: winNum 2 overlap current 0
   mvPexInit:Warning :Bar 2 size is illigal
   it will be disabled
   please check Pex and CPU windows configuration
   Request resource failed - PEX 0
   PCI: bus0: Fast back to back transfers enabled
   PCI: bus1: Fast back to back transfers enabled
   SCSI subsystem initialized
   usbcore: registered new driver usbfs
   usbcore: registered new driver hub
   use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
   Done.
   cesadev_init(c0011b74)
   Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
   SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
   SGI XFS Quota Management subsystem
   Initializing Cryptographic API
   io scheduler noop registered
   io scheduler anticipatory registered (default)
   io scheduler deadline registered
   io scheduler cfq registered
   Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
   serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
   serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
   RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
   loop: loaded (max 8 devices)
   Marvell Gigabit Ethernet Driver 'egiga':
     o Ethernet descriptors in DRAM
     o DRAM SW cache-coherency
     o Checksum offload enabled
     o Loading network interface ** egiga_init_module (0)
   'eth0'
   Intergrated Sata device found
   scsi0 : Marvell SCSI to SATA adapter
   scsi1 : Marvell SCSI to SATA adapter
   ** BUFFALO Disable Command Queuing Function [0 0] **
   ** BUFFALO Disable Command Queuing Function [0 1] **
     Vendor: SAMSUNG   Model: HD501LJ           Rev: CR10
     Type:   Direct-Access                      ANSI SCSI revision: 03
     Vendor: SAMSUNG   Model: HD501LJ           Rev: CR10
     Type:   Direct-Access                      ANSI SCSI revision: 03
   Linux IAL (ERROR) : retry command host=0, bus=0 SCpnt = c37bbba0
   SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
   sda: Write Protect is off
   SCSI device sda: drive cache: write back
   SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
   sda: Write Protect is off
   SCSI device sda: drive cache: write back
   sda: sda1 sda2 sda4 < sda5 sda6 >
   sd 0:0:0:0: Attached scsi disk sda
   Linux IAL (ERROR) : retry command host=1, bus=1 SCpnt = c37bbba0
   SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
   sdb: Write Protect is off
   SCSI device sdb: drive cache: write back
   SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
   sdb: Write Protect is off
   SCSI device sdb: drive cache: write back
   sdb: sdb1 sdb2 sdb4 < sdb5 sdb6 >
   sd 1:0:0:0: Attached scsi disk sdb
   sd 0:0:0:0: Attached scsi generic sg0 type 0
   sd 1:0:0:0: Attached scsi generic sg1 type 0
   physmap flash device: 400000 at ff800000
   >jedec_probe
   Found: SST 39LF020
   phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
   number of JEDEC chips: 1
   cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
   cmdlinepart partition parsing not available
   RedBoot partition parsing not available
   ehci_platform ehci_platform.4523: EHCI Platform Host Controller
   ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
   ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
   ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
   usb usb1: Product: EHCI Platform Host Controller
   usb usb1: Manufacturer: Linux 2.6.16.16-teralive110gpl4LSPro-mb_v6 ehci_hcd
   usb usb1: SerialNumber: ehci_platform.4523
   usb usb1: configuration #1 chosen from 1 choice
   hub 1-0:1.0: USB hub found
   hub 1-0:1.0: 1 port detected
   ehci_platform ehci_platform.16781: EHCI Platform Host Controller
   ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
   ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
   ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
   usb usb2: Product: EHCI Platform Host Controller
   usb usb2: Manufacturer: Linux 2.6.16.16-teralive110gpl4LSPro-mb_v6 ehci_hcd
   usb usb2: SerialNumber: ehci_platform.16781
   usb usb2: configuration #1 chosen from 1 choice
   hub 2-0:1.0: USB hub found
   hub 2-0:1.0: 1 port detected
   USB Universal Host Controller Interface driver v2.3
   usbcore: registered new driver usblp
   drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
   Initializing USB Mass Storage driver...
   usbcore: registered new driver usb-storage
   USB Mass Storage support registered.
   mice: PS/2 mouse device common for all mice
   md: linear personality registered for level -1
   md: raid0 personality registered for level 0
   md: raid1 personality registered for level 1
   md: raid5 personality registered for level 5
   md: raid4 personality registered for level 4
   raid5: measuring checksumming speed
      arm4regs  :   308.800 MB/sec
      8regs     :   217.600 MB/sec
      32regs    :   252.400 MB/sec
   raid5: using function: arm4regs (308.800 MB/sec)
   md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
   md: bitmap version 4.39
   Kernel event proc (C) BUFFALO INC. V.1.00 installed.
   MICON ctrl (C) BUFFALO INC. V.1.00 installed.
   MICON V2 (C) BUFFALO INC. V.1.00 installed.
   NET: Registered protocol family 2
   IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
   TCP established hash table entries: 4096 (order: 2, 16384 bytes)
   TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
   TCP: Hash tables configured (established 4096 bind 4096)
   TCP reno registered
   TCP bic registered
   NET: Registered protocol family 1
   NET: Registered protocol family 17
   md: Autodetecting RAID arrays.
   md: autorun ...
   md: considering sdb6 ...
   md:  adding sdb6 ...
   md:  adding sda6 ...
   md: created md2
   md: bind<sda6>
   md: bind<sdb6>
   md: running: <sdb6><sda6>
   raid1: raid set md2 active with 2 out of 2 mirrors
   md: ... autorun DONE.
   RAMDISK: Compressed image found at block 0
   EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
   VFS: Mounted root (ext2 filesystem).
   ---- in Modified linuxrc ---
   Thu Mar 20 20:17:05 JST 2008
   err: RecvPacket: readlen=0.
   kjournald starting.  Commit interval 5 seconds
   EXT3 FS on sda1, internal journal
   EXT3-fs: recovery complete.
   EXT3-fs: mounted filesystem with ordered data mode.
   err: RecvPacket: readlen=0.
   err: RecvPacket: readlen=0.
   err: RecvPacket: readlen=0.
   err: RecvPacket: readlen=0.
   linuxrc:choose operation (timeout 4[s])
   1:RamRoot other:HddRoot  ? -HddRoot-
   KERNEL:2007/11/3 23:17:32
   HDD:2007/6/28 9:42:0
   >>> Not expected kernel version, upgrade /etc/linkstation_release
   Bypassing CopyFromInitrdToHdd
   checking local disk....
   fsck 1.27 (8-Mar-2002)
   e2fsck 1.27 (8-Mar-2002)
   fsck.ext2: Filesystem has unsupported feature(s) (/dev/ls_disk1_1)
   e2fsck: Get a newer version of e2fsck!
   done
   XFS mounting filesystem sda2
   Starting XFS recovery on filesystem: sda2 (logdev: internal)
   Ending XFS recovery on filesystem: sda2 (logdev: internal)
   VFS: Mounted root (xfs filesystem).
   Trying to move old root to /initrd ... okay
   Freeing init memory: 116K
   INIT: version 2.86 booting
   * .udev/ already exists on the static /dev!
   Starting the hotplug events dispatcher: udevdudevd[357]: main: the kernel does not support inotify, udevd cans
   .
   Synthesizing the initial hotplug events...SAL (ERROR)  0 0 0 :Scsi command completed. pScb c37162c0, ScsiStatD
   SAL (ERROR) CDB:12 1 0 0 fe 0
   SAL (ERROR) Sense Data:70 0 5 0 0 0 0 a 0 0 0 0 24 0 0 0 0 0
   SAL (ERROR)  0 1 0 :Scsi command completed. pScb c37162c0, ScsiStatus 2 completionStatus MV_SCSI_COMPLETION_BD
   SAL (ERROR) CDB:12 1 0 0 fe 0
   SAL (ERROR) Sense Data:70 0 5 0 0 0 0 a 0 0 0 0 24 0 0 0 0 0
   SAL (ERROR)  0 0 0 :Scsi command completed. pScb c37162c0, ScsiStatus 2 completionStatus MV_SCSI_COMPLETION_BD
   SAL (ERROR) CDB:12 1 0 0 fe 0
   SAL (ERROR) Sense Data:70 0 5 0 0 0 0 a 0 0 0 0 24 0 0 0 0 0
   SAL (ERROR)  0 1 0 :Scsi command completed. pScb c37162c0, ScsiStatus 2 completionStatus MV_SCSI_COMPLETION_BD
   SAL (ERROR) CDB:12 1 0 0 fe 0
   SAL (ERROR) Sense Data:70 0 5 0 0 0 0 a 0 0 0 0 24 0 0 0 0 0
   done.
   Waiting for /dev to be fully populated...done.
   GSetting parameters of disc: (none).
   Activating swap:swapon on /dev/sda5
   Adding 1004020k swap on /dev/sda5.  Priority:-1 extents:1 across:1004020k
   swapon on /dev/sdb5
   Adding 1003896k swap on /dev/sdb5.  Priority:-2 extents:1 across:1003896k
   .
   Setting the system clock..
   System Clock set. Local time: Thu Mar 20 20:17:52 UTC 2008.
   Cleaning up ifupdown....
   Loading device-mapper support.
   Generating udev events for MD arrays...done.
   Will now check all file systems.
   fsck 1.40-WIP (14-Nov-2006)
   Checking all file systems.
   [/sbin/fsck.ext3 (1) -- /boot] fsck.ext3 -y -C0 /dev/sda1
   e2fsck 1.40-WIP (14-Nov-2006)
   /dev/sda1: clean, 22/125696 files, 11344/251007 blocks
   Done checking file systems.
   A log is being saved in /var/log/fsck/checkfs if that location is writable.
   Setting kernel variables...done.
   Will now mount local filesystems:mount: none already mounted or /dev/pts busy
   mount: according to mtab, devpts is already mounted on /dev/pts
   kjournald starting.  Commit interval 5 seconds
   EXT3 FS on sda1, internal journal
   EXT3-fs: mounted filesystem with ordered data mode.
   EXT3-fs: journalled quota options not supported.
   EXT3-fs: journalled quota options not supported.
   kjournald starting.  Commit interval 5 seconds
   EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
   EXT3 FS on md2, internal journal
   EXT3-fs: recovery complete.
   EXT3-fs: mounted filesystem with ordered data mode.
   failed!
   Will now activate swapfile swap:done.
   Cleaning /var/run...done.
   Cleaning /var/lock...done.
   Setting up resolvconf...done.
   Setting up networking....
   * /etc/network/options is deprecated (see README.Debian of netbase).
   Setting up IP spoofing protection...done (rp_filter).
   Configuring network interfaces...eth0: link down
   done.
   Start services: micro_evtd
   Starting portmap daemon....
   eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
   Setting console screen modes and fonts.
   Starting kernelmon:Initializing random number generator...done.
   INIT: Entering runlevel: 2
   err: RecvPacket: readlen=0.

Possible u-boot commands

   Marvell>> help
   ?       - alias for 'help'
   base    - print or set address offset
   board_info   -show board information.
   boot    - boot default, i.e., run 'bootcmd'
   bootd   - boot default, i.e., run 'bootcmd'
   bootend - with micon. send bootend.
   bootm   - boot application image from memory
   bootp   - boot image via network using BootP/TFTP protocol
   bubt    - Burn an image on the Boot Flash.
   buzzer          - with micon. buzzer command.
   cmp     - memory compare
   cp      - memory copy
   cpumap - Display CPU memory mapping settings.
   crc32   - checksum calculation
   date    - get/set/reset date & time
   diskboot- boot from IDE device
   echo    - echo args to console
   erase   - erase FLASH memory
   ext2load- load binary file from a Ext2 filesystem
   ext2ls- list files in a directory (default /)
   fan_control     - with micon. fan control  .
   fan_rpm         - with micon. fan get rpm.
   flinfo  - print FLASH memory information
   get_sw          - without micon. get switch status.
   go      - start application at address 'addr'
   hdd_power       - hdd power control  .
   help    - print online help
   ide     - IDE sub-system
   led             - without micon. call led control routine(for debug).
   led_blink       - with micon. led blink control setting.
   led_cpu_mcon    - with micon. led cpu micon control setting.
   led_on_off      - with micon. led on off control setting.
   loop    - infinite loop on address range
   md      - memory display
   micon           - with micon. command(2byte hex) -data(witin 32byte hex)
   mm      - memory modify (auto-incrementing)
   mtest   - simple RAM test
   mw      - memory write (fill)
   nm      - memory modify (constant address)
   pci     - list and access PCI Configuraton Space
   printenv- print environment variables
   protect - enable or disable FLASH write protection
   rarpboot- boot image via network using RARP/TFTP protocol
   reset   - Perform RESET of the CPU
   resetenv        - Return all environment variable to default.
   saveenv - save environment variables to persistent storage
   security -device -command -options -password
   setenv  - set environment variables
   shutdown        - with micon. Poff .
   sw_power        - with micon. software power control interface
   tftpboot- boot image via network using TFTP protocol
   usb_power       - without micon. usb power control  .
   version - print monitor version