Difference between revisions of "LS Mini: Serial Port Output - Boot-Log"

From NAS-Central Buffalo - The Linkstation Wiki
Jump to: navigation, search
m (New page: =Serial Port Output= ==Bootup Sequence== <pre> Orion1 CPU = Low ...)
 
(Uboot env settings: moved to separate page)
 
(6 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 +
{{Articles|Hardware|LS-WSGL/R1}}
 +
[[Image:LS_WSGL.jpg|thumb|right|Linkstation Mini]]
 
=Serial Port Output=
 
=Serial Port Output=
  
Line 117: Line 119:
 
</pre>
 
</pre>
  
==Uboot env settings==
+
== U-Boot settings ==
<pre>
+
[[LS Mini: Serial Port Output - U-Boot]]
Marvell>> printenv
+
bootargs=$(bootargs_base) $(bootargs_root)
+
baudrate=115200
+
loads_echo=0
+
ipaddr=192.168.11.150
+
serverip=192.168.11.1
+
rootpath=/nfs/arm
+
cpuName=926
+
CASset=min
+
MALLOC_len=4
+
bootargs_end=:::DB88FXX81:eth0:none
+
ethact=egiga0
+
ethaddr=00:1D:73:4C:92:E3
+
buffalo_ver=BOOTVER=1.13
+
buffalo_minor_ver=BOOT_MINOR_VER=1.00
+
build_time=18:48:49
+
initrd=initrd.buffalo
+
kernel=uImage.buffalo
+
bootargs_base=console=ttyS0,115200
+
bootargs_root=root=/dev/sda2 rw initrd=0x00800040,15M panic=5
+
def_tftp=tftp 0x00100000 $(kernel); tftp 0x00800000 $(initrd); setenv bootargs $(bootargs0
+
stdin=serial
+
stdout=serial
+
stderr=serial
+
enaMonExt=no
+
enaFlashBuf=yes
+
enaCpuStream=no
+
ethprime=egiga0
+
bootdelay=3
+
disaMvPnp=no
+
overEthAddr=no
+
usb0Mode=host
+
usb1Mode=host
+
bootargs_func=func=0
+
filesize=5636A9
+
force_tftp=1
+
bootcmd=tftp 0x00100000 $(kernel); tftp 0x00800000 $(initrd); setenv bootargs $(bootargs_0
+
  
Environment size: 1029/4092 bytes
+
=Settings=
Marvell>>  
+
 
</pre>
+
==cat /proc/cpuinfo==
 +
Processor      : ARM926EJ-Sid(wb) rev 0 (v5l)
 +
BogoMIPS        : 266.24
 +
Features        : swp half thumb fastmult edsp java
 +
CPU implementer : 0x41
 +
CPU architecture: 5TEJ
 +
CPU variant    : 0x0
 +
CPU part        : 0x926
 +
CPU revision    : 0
 +
Cache type      : write-back
 +
Cache clean    : cp15 c7 ops
 +
Cache lockdown  : format C
 +
Cache format    : Harvard
 +
I size         : 32768
 +
I assoc        : 1
 +
I line length  : 32
 +
I sets          : 1024
 +
D size          : 32768
 +
D assoc        : 1
 +
D line length  : 32
 +
D sets          : 1024
 +
Hardware        : MV-88fxx81
 +
Revision        : 0000
 +
Serial          : 0000000000000000
 +
 
 +
==cat /proc/meminfo==
 +
MemTotal:      126236 kB
 +
MemFree:        62112 kB
 +
Buffers:          100 kB
 +
Cached:          38176 kB
 +
SwapCached:          0 kB
 +
Active:          33444 kB
 +
Inactive:        19396 kB
 +
HighTotal:          0 kB
 +
HighFree:            0 kB
 +
LowTotal:      126236 kB
 +
LowFree:        62112 kB
 +
SwapTotal:    1003896 kB
 +
SwapFree:      1003896 kB
 +
Dirty:              36 kB
 +
Writeback:          0 kB
 +
Mapped:          21212 kB
 +
Slab:            7928 kB
 +
CommitLimit:  1067012 kB
 +
Committed_AS:  172968 kB
 +
PageTables:        696 kB
 +
VmallocTotal:  385024 kB
 +
VmallocUsed:      1040 kB
 +
VmallocChunk:  383984 kB
 +
 
 +
==cat /proc/interrupts==
 +
            CPU0
 +
  0:      9197  Mv Timer Tick
 +
  3:        351  serial
 +
  21:        45  eth0
 +
  29:      1180  mvSata
 +
  47:          0  FuncSw
 +
Err:          0
 +
 
 +
==lsmod==
 +
Module                  Size  Used by
 +
appletalk              38544  0
 +
psnap                  4516  1 appletalk
 +
llc                    8372  1 psnap
 +
usblp                  14784  0
 +
usb_storage            59975  0
 +
ehci_marvell_hcd      33480  0
 +
usbcore              127240  4 usblp,usb_storage,ehci_marvell_hcd
 +
 
 +
==cat /proc/buffalo/firmware==
 +
SERIES=LinkStation
 +
PRODUCTNAME=LS-WSGL/R1(SUJIN)
 +
VERSION=0.16
 +
SUBVERSION=FLASH 0.00
 +
PRODUCTID=0x00003002
 +
BUILDDATE=2008/03/12 11:17:32
 +
BOOTVER=1.13
 +
 
 +
==mount==
 +
rootfs on / type rootfs (rw)
 +
/dev/root on / type xfs (rw)
 +
proc on /proc type proc (rw)
 +
sysfs on /sys type sysfs (rw)
 +
devpts on /dev/pts type devpts (rw)
 +
/dev/ram1 on /mnt/ram type tmpfs (rw)
 +
/dev/md0 on /boot type ext3 (rw,data=ordered)
 +
usbfs on /proc/bus/usb type usbfs (rw)
 +
/dev/md2 on /mnt/array1 type xfs (rw,noatime,sunit=128,swidth=256)
 +
 
 +
==uname -r==
 +
2.6.16.16-arm1
 +
 
 +
==cat /proc/cmdline==
 +
console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOT
 +
VER=1.13
 +
 
 +
==cat /proc/mtd==
 +
dev:    size  erasesize  name
 +
mtd0: 00040000 00001000 "phys_mapped_flash"
 +
 
 +
==Partitions:==
 +
root@LS-WSGLBA4:/proc# cat partitions
 +
major minor  #blocks  name
 +
 +
    8    0  488386584 sda
 +
    8    1    1004031 sda1
 +
    8    2    5004247 sda2
 +
    8    4          1 sda4
 +
    8    5    1004031 sda5
 +
    8    6  480480021 sda6
 +
    8    16  488386584 sdb
 +
    8    17    1004031 sdb1
 +
    8    18    5004247 sdb2
 +
    8    20          1 sdb4
 +
    8    21    1004031 sdb5
 +
    8    22  480480021 sdb6
 +
  31    0        256 mtdblock0
 +
    9    0    1003904 md0
 +
    9    10    1003904 md10
 +
    9    1    5004160 md1
 +
    9    2  960959872 md2
 +
 
 +
==ls /proc==
 +
1              1516          5941          buffalo        misc
 +
1046          1566          600            bus            modules
 +
1049          1567          601            cmdline        mounts
 +
11            168            6012          cpu            mtd
 +
1172          169            6017          cpuinfo        net
 +
1173          1703          6018          crypto        partitions
 +
1263          192            6674          devices        resource_dump
 +
1303          2              6726          diskstats      scsi
 +
1310          3              6770          dma_copy      self
 +
1311          327            6774          driver        slabinfo
 +
1312          38            6790          execdomains    stat
 +
1319          39            6796          filesystems    swaps
 +
1333          4              6812          fs            sys
 +
1358          40            6824          interrupts    sysvipc
 +
1367          41            6850          iomem          tty
 +
1370          42            7918          ioports        uptime
 +
1486          43            847            kallsyms      version
 +
1487          44            8947          kmsg          vmstat
 +
1499          45            909            loadavg        zoneinfo
 +
1507          491            9655          locks
 +
1510          494            9656          mdstat
 +
1514          5              buddyinfo      meminfo
 +
 
 +
==cat /proc/buffalo/enet==
 +
MAC=00:1D:73:4C:XX:XX
 +
link=100Mbps
 +
duplex=full
 +
jumboframe=enable
 +
mtu=1500
 +
regster9 value=0x0300
 +
mode.config=auto:slave
 +
mode.actual=master
 +
=== for debug ===
 +
 +
 +
page=0 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
 +
        0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
 +
        0x6060 0x6c08 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
 +
        0x0000 0x0000 0x0040 0x0000 0x0000 0x0000 0x0000 0x0000
 +
 +
page=1 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
 +
        0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
 +
        0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0001 0x0000
 +
        0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
 +
 +
page=2 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
 +
        0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
 +
        0x0288 0x0000 0x0000 0x0008 0x0000 0x1070 0x0002 0x0000
 +
        0x4705 0x0044 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
 +
 +
page=3 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
 +
        0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
 +
        0x0201 0x4401 0x4105 0x0073 0x0000 0x0000 0x0003 0x0000
 +
        0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
 +
 +
page=4 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
 +
        0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
 +
        0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0004 0x0000
 +
        0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
 +
 +
page=5 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
 +
        0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
 +
        0x80ff 0xa0ff 0x80ff 0x89ff 0x0000 0x2000 0x0005 0x0603
 +
        0x0000 0x0104 0x0f12 0x0a0c 0x0006 0x0000 0x0000 0x0000
 +
 +
page=6 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
 +
        0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
 +
        0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0006 0x0000
 +
        0x0000 0x0000 0x0010 0x0000 0x0000 0x0000 0x0000 0x0000
 +
 +
page=7 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
 +
        0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
 +
        0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0007 0x0000
 +
        0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
 +
 +
page=8 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
 +
        0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
 +
        0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0008 0x0000
 +
        0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
 +
 +
page=9 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
 +
        0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
 +
        0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0009 0x0000
 +
        0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
 +
 
 +
==dmesg==
 +
Linux version 2.6.16.16-arm1 (root@I.You) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #316 Tue Jul 22 16:22:33 JST 2008
 +
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
 +
Machine: MV-88fxx81
 +
Using UBoot passing parameters structure
 +
Sys Clk = 200000000, Tclk = 166664740
 +
 +
 +
- Warning - This LSP release was tested only with U-Boot release 1.7.3
 +
 +
Memory policy: ECC disabled, Data cache writeback
 +
On node 0 totalpages: 32768
 +
  DMA zone: 32768 pages, LIFO batch:7
 +
  DMA32 zone: 0 pages, LIFO batch:0
 +
  Normal zone: 0 pages, LIFO batch:0
 +
  HighMem zone: 0 pages, LIFO batch:0
 +
CPU0: D VIVT write-back cache
 +
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
 +
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
 +
Built 1 zonelists
 +
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOTVER=1.13
 +
PID hash table entries: 1024 (order: 10, 16384 bytes)
 +
Console: colour dummy device 80x30
 +
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
 +
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
 +
Memory: 128MB 0MB 0MB 0MB = 128MB total
 +
Memory: 110620KB available (2992K code, 553K data, 112K init)
 +
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
 +
Mount-cache hash table entries: 512
 +
CPU: Testing write buffer coherency: ok
 +
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
 +
Freeing initrd memory: 15360K
 +
NET: Registered protocol family 16
 +
FLASH boardId = 19
 +
Flash bankwidth 1, base ff800000, size 40000
 +
BUFFALO LS_WSGL_R1 FLASH size 256[KB]
 +
 +
  Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_WSGL_R1
 +
 +
Detected Tclk 166664740 and SysClk 200000000
 +
Marvell USB EHCI Host controller #0: c16f5e00
 +
Marvell USB EHCI Host controller #1: c16f5c00
 +
pexBarOverlapDetect: winNum 2 overlap current 0
 +
mvPexInit:Warning :Bar 2 size is illigal
 +
it will be disabled
 +
please check Pex and CPU windows configuration
 +
PCI: bus0: Fast back to back transfers enabled
 +
PCI: bus1: Fast back to back transfers enabled
 +
SCSI subsystem initialized
 +
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
 +
Done.
 +
cesadev_init(c0011c44)
 +
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
 +
SGI XFS with large block numbers, no debug enabled
 +
Initializing Cryptographic API
 +
io scheduler noop registered (default)
 +
io scheduler anticipatory registered
 +
io scheduler deadline registered
 +
io scheduler cfq registered
 +
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
 +
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
 +
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
 +
RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
 +
loop: loaded (max 8 devices)
 +
Marvell Gigabit Ethernet Driver 'egiga':
 +
  o Ethernet descriptors in DRAM
 +
  o DRAM SW cache-coherency
 +
  o Checksum offload enabled
 +
  o Loading network interface ** egiga_init_module (0)
 +
'eth0'
 +
Intergrated Sata device found
 +
scsi0 : Marvell SCSI to SATA adapter
 +
scsi1 : Marvell SCSI to SATA adapter
 +
** BUFFALO Disable Command Queuing Function [0 0] **
 +
** BUFFALO Disable Command Queuing Function [0 1] **
 +
  Vendor: Hitachi  Model: HTS545050KTA300  Rev: BKFO
 +
  Type:  Direct-Access                      ANSI SCSI revision: 03
 +
  Vendor: Hitachi  Model: HTS545050KTA300  Rev: BKFO
 +
  Type:  Direct-Access                      ANSI SCSI revision: 03
 +
Linux IAL (ERROR) : retry command host=0, bus=0 SCpnt = c1422ba0
 +
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
 +
sda: Write Protect is off
 +
sda: Mode Sense: 23 00 00 00
 +
SCSI device sda: drive cache: write back
 +
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
 +
sda: Write Protect is off
 +
sda: Mode Sense: 23 00 00 00
 +
SCSI device sda: drive cache: write back
 +
sda: sda1 sda2 sda4 < sda5 sda6 >
 +
sd 0:0:0:0: Attached scsi disk sda
 +
Linux IAL (ERROR) : retry command host=1, bus=1 SCpnt = c1422ba0
 +
SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
 +
sdb: Write Protect is off
 +
sdb: Mode Sense: 23 00 00 00
 +
SCSI device sdb: drive cache: write back
 +
SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
 +
sdb: Write Protect is off
 +
sdb: Mode Sense: 23 00 00 00
 +
SCSI device sdb: drive cache: write back
 +
sdb: sdb1 sdb2 sdb4 < sdb5 sdb6 >
 +
sd 1:0:0:0: Attached scsi disk sdb
 +
sd 0:0:0:0: Attached scsi generic sg0 type 0
 +
sd 1:0:0:0: Attached scsi generic sg1 type 0
 +
physmap flash device: 40000 at ff800000
 +
CFI: Found no phys_mapped_flash device at location zero
 +
>jedec_probe
 +
Found: SST 39LF020
 +
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
 +
number of JEDEC chips: 1
 +
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
 +
cmdlinepart partition parsing not available
 +
RedBoot partition parsing not available
 +
mice: PS/2 mouse device common for all mice
 +
md: raid0 personality registered for level 0
 +
md: raid1 personality registered for level 1
 +
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
 +
md: bitmap version 4.39
 +
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
 +
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
 +
mvGppValueSet: Err. An attempt to set output value to GPP 15 in input mode.
 +
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
 +
mvGppValueSet: Err. An attempt to set output value to GPP 2 in input mode.
 +
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.0.02 installed.
 +
NET: Registered protocol family 2
 +
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
 +
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
 +
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
 +
TCP: Hash tables configured (established 8192 bind 8192)
 +
TCP reno registered
 +
TCP bic registered
 +
NET: Registered protocol family 1
 +
NET: Registered protocol family 17
 +
md: Autodetecting RAID arrays.
 +
md: autorun ...
 +
md: ... autorun DONE.
 +
RAMDISK: Compressed image found at block 0
 +
VFS: Mounted root (ext2 filesystem).
 +
md: md10 stopped.
 +
md: md1 stopped.
 +
md: md0 stopped.
 +
md: bind<sdb1>
 +
md: bind<sda1>
 +
raid1: raid set md0 active with 2 out of 2 mirrors
 +
kjournald starting.  Commit interval 5 seconds
 +
EXT3 FS on md0, internal journal
 +
EXT3-fs: mounted filesystem with ordered data mode.
 +
md: md10 stopped.
 +
md: bind<sdb5>
 +
md: bind<sda5>
 +
raid1: raid set md10 active with 2 out of 2 mirrors
 +
md: md1 stopped.
 +
md: bind<sdb2>
 +
md: bind<sda2>
 +
raid1: raid set md1 active with 2 out of 2 mirrors
 +
XFS mounting filesystem md1
 +
Ending clean XFS mount for filesystem: md1
 +
XFS mounting filesystem md1
 +
Ending clean XFS mount for filesystem: md1
 +
VFS: Mounted root (xfs filesystem).
 +
Trying to move old root to /initrd ... okay
 +
Freeing init memory: 112K
 +
Adding 1003896k swap on /dev/md10.  Priority:-1 extents:1 across:1003896k
 +
kjournald starting.  Commit interval 5 seconds
 +
EXT3 FS on md0, internal journal
 +
EXT3-fs: mounted filesystem with ordered data mode.
 +
usbcore: registered new driver usbfs
 +
usbcore: registered new driver hub
 +
ehci_platform ehci_platform.4523: EHCI Platform Host Controller
 +
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
 +
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
 +
ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
 +
usb usb1: configuration #1 chosen from 1 choice
 +
hub 1-0:1.0: USB hub found
 +
hub 1-0:1.0: 1 port detected
 +
ehci_platform ehci_platform.16781: EHCI Platform Host Controller
 +
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
 +
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
 +
ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
 +
usb usb2: configuration #1 chosen from 1 choice
 +
hub 2-0:1.0: USB hub found
 +
hub 2-0:1.0: 1 port detected
 +
Initializing USB Mass Storage driver...
 +
usbcore: registered new driver usb-storage
 +
USB Mass Storage support registered.
 +
usbcore: registered new driver usblp
 +
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
 +
eth0: link down
 +
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
 +
md: md2 stopped.
 +
md: bind<sdb6>
 +
md: bind<sda6>
 +
md2: setting max_sectors to 128, segment boundary to 32767
 +
raid0: looking at sda6
 +
raid0:  comparing sda6(480479936) with sda6(480479936)
 +
raid0:  END
 +
raid0:  ==> UNIQUE
 +
raid0: 1 zones
 +
raid0: looking at sdb6
 +
raid0:  comparing sdb6(480479936) with sda6(480479936)
 +
raid0:  EQUAL
 +
raid0: FINAL 1 zones
 +
raid0: done.
 +
raid0 : md_size is 960959872 blocks.
 +
raid0 : conf->hash_spacing is 960959872 blocks.
 +
raid0 : nb_zone is 1.
 +
raid0 : Allocating 4 bytes for hash.
 +
XFS mounting filesystem md2
 +
Ending clean XFS mount for filesystem: md2
 +
BuffaloSwPollingCheck> SW_POWER_ON
 +
NET: Registered protocol family 5
 +
eth0: change mtu 1500 (buffer-size 1520) to 9676 (buffer-size 9696)
 +
eth0: link down
 +
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
 +
 
 +
==df==                 
 +
Filesystem          1k-blocks      Used Available Use% Mounted on
 +
/dev/md1              4993920    255660  4738260  5% /
 +
/dev/ram1                15360      112    15248  1% /mnt/ram
 +
/dev/md0                988088    116632    871456  12% /boot
 +
/dev/md2            480348864      3268 480345596  0% /mnt/array1
 +
 
 +
==mount==
 +
rootfs on / type rootfs (rw)
 +
/dev/root on / type xfs (rw)
 +
proc on /proc type proc (rw)
 +
sysfs on /sys type sysfs (rw)
 +
devpts on /dev/pts type devpts (rw)
 +
/dev/ram1 on /mnt/ram type tmpfs (rw)
 +
/dev/md0 on /boot type ext3 (rw,data=ordered)
 +
usbfs on /proc/bus/usb type usbfs (rw)
 +
/dev/md2 on /mnt/array1 type xfs (rw,noatime)
 +
 
 +
==smartctl -a /dev/sda (same for second drive)==
 +
smartctl version 5.37 [armv5tejl-unknown-linux-gnu] Copyright (C) 2002-6 Bruce Allen
 +
Home page is http://smartmontools.sourceforge.net/
 +
 +
=== START OF INFORMATION SECTION ===
 +
Device Model:    Hitachi HTS545050KTA300
 +
Serial Number:    080227BK0F00VEG0H--A
 +
Firmware Version: BKFOC60M
 +
User Capacity:    500,107,862,016 bytes
 +
Device is:        Not in smartctl database [for details use: -P showall]
 +
ATA Version is:  8
 +
ATA Standard is:  Not recognized. Minor revision code: 0x42
 +
Local Time is:    Fri Jul 25 23:42:28 2008 JST
 +
SMART support is: Available - device has SMART capability.
 +
SMART support is: Disabled
 +
 +
SMART Disabled. Use option -s with argument 'on' to enable it.
 +
 
 +
smartctl -A /dev/sda (sync in progress, note temperature)
 +
 
 +
=== START OF READ SMART DATA SECTION ===
 +
SMART Attributes Data Structure revision number: 16
 +
Vendor Specific SMART Attributes with Thresholds:
 +
ID# ATTRIBUTE_NAME          FLAG    VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
 +
  1 Raw_Read_Error_Rate    0x000b  100  100  062    Pre-fail  Always      -      0
 +
  2 Throughput_Performance  0x0005  100  100  040    Pre-fail  Offline      -      0
 +
  3 Spin_Up_Time            0x0007  236  236  033    Pre-fail  Always      -      1
 +
  4 Start_Stop_Count        0x0012  100  100  000    Old_age  Always      -      14
 +
  5 Reallocated_Sector_Ct  0x0033  100  100  005    Pre-fail  Always      -      0
 +
  7 Seek_Error_Rate        0x000b  100  100  067    Pre-fail  Always      -      0
 +
  8 Seek_Time_Performance  0x0005  100  100  040    Pre-fail  Offline      -      0
 +
  9 Power_On_Hours          0x0012  100  100  000    Old_age  Always      -      1
 +
  10 Spin_Retry_Count        0x0013  100  100  060    Pre-fail  Always      -      0
 +
  12 Power_Cycle_Count      0x0032  100  100  000    Old_age  Always      -      14
 +
191 G-Sense_Error_Rate      0x000a  100  100  000    Old_age  Always      -      0
 +
192 Power-Off_Retract_Count 0x0032  100  100  000    Old_age  Always      -      12
 +
193 Load_Cycle_Count        0x0012  100  100  000    Old_age  Always      -      143
 +
194 Temperature_Celsius    0x0002  096  096  000    Old_age  Always      -      57 (Lifetime Min/Max 25/57)
 +
196 Reallocated_Event_Count 0x0032  100  100  000    Old_age  Always      -      0
 +
197 Current_Pending_Sector  0x0022  100  100  000    Old_age  Always      -      0
 +
198 Offline_Uncorrectable  0x0008  100  100  000    Old_age  Offline      -      0
 +
199 UDMA_CRC_Error_Count    0x000a  200  200  000    Old_age  Always      -      0
 +
223 Load_Retry_Count        0x000a  100  100  000    Old_age  Always      -      0
 +
 
 +
==reboot procedure==
 +
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0)
 +
  <0>Rebooting in 90 seconds..
 +
BuffaloChangePowerStatusBeforeHalt > Check power status. MagicKey = 24
 +
BuffaloChangePowerStatusBeforeHalt > Changed to 43 from 24

Latest revision as of 02:51, 29 September 2008

Linkstation Mini

Contents

Serial Port Output

Bootup Sequence

                                                         
Orion1   CPU =  Low                                       
                                                         
> Checking hardware info ...                             
=== Strap status : 0x00802030 ===
=== H/W boardId  :       0x33 ===
=== boardId      :       0x1a ===
=== micon_support:        off ===
> OK.
=== BUFFALO LS-WSGL/R1 U-Boot. ===
** LOADER **
** BUFFALO BOARD: BUFFALO_BOARD_LS_WSGL/R1 LE (CFG_ENV_ADDR=fffff000)


U-Boot 1.1.1 (Feb 22 2008 - 18:48:54) Marvell version: 1.12.1 - TINY
Buffalo Version: 1.13-1.00

DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done

Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166Mhz


USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Using 88E1118 phy
buffalo_change_power_status > Read 0x3a
buffalo_IsStopAtUbootStatus > MagicKey=0x3a
buffalo_change_power_status > Read 0x3a
buffalo_change_power_status > Read 0x3a
buffalo_change_power_status > Writing 0x5c

Please Press HDD power button to continue ...
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Writing 0x3a

Marvell Serial ATA Adapter
Integrated Sata device found
  Device 0: OK
Model: Hitachi HTS545050KTA300                  Firm: BKFOC60M Ser#: 080426BK0F00VEG30JDA
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
  Device 1: OK
Model: Hitachi HTS545050KTA300                  Firm: BKFOC60M Ser#: 080426BK0F00VEG30BXA
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)

Using device ide0, partition 1

Loading from block device ide device 0, partition 1: Name: hda1
  Type: U-Boot  File:/uImage.buffalo

1757600 bytes read
   Image Name:   Linux-2.6.16.16-arm1
   Created:      2008-05-20   2:17:17 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1757536 Bytes =  1.7 MB
   Load Address: 00008000
   Entry Point:  00008000
Using device ide0, partition 1

Loading from block device ide device 0, partition 1: Name: hda1
  Type: U-Boot  File:/initrd.buffalo

5650089 bytes read
   Image Name:   initrd
   Created:      2008-05-20   2:18:09 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    5650025 Bytes =  5.4 MB
   Load Address: 00000000
   Entry Point:  00000000
Using device ide1, partition 1

Loading from block device ide device 1, partition 1: Name: hdb1
  Type: U-Boot  File:/uImage.buffalo

1757600 bytes read
   Image Name:   Linux-2.6.16.16-arm1
   Created:      2008-05-20   2:17:17 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1757536 Bytes =  1.7 MB
   Load Address: 00008000
   Entry Point:  00008000
Using device ide1, partition 1

Loading from block device ide device 1, partition 1: Name: hdb1
  Type: U-Boot  File:/initrd.buffalo

5650089 bytes read
   Image Name:   initrd
   Created:      2008-05-20   2:18:09 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    5650025 Bytes =  5.4 MB
   Load Address: 00000000
   Entry Point:  00000000
Booting from Device 0
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0
switched to TFTP boot.
Hit any key to stop autoboot:  0
Marvell>> 

U-Boot settings

LS Mini: Serial Port Output - U-Boot

Settings

cat /proc/cpuinfo

Processor       : ARM926EJ-Sid(wb) rev 0 (v5l)
BogoMIPS        : 266.24
Features        : swp half thumb fastmult edsp java
CPU implementer : 0x41
CPU architecture: 5TEJ
CPU variant     : 0x0
CPU part        : 0x926
CPU revision    : 0
Cache type      : write-back
Cache clean     : cp15 c7 ops
Cache lockdown  : format C
Cache format    : Harvard
I size          : 32768
I assoc         : 1
I line length   : 32
I sets          : 1024
D size          : 32768
D assoc         : 1
D line length   : 32
D sets          : 1024
Hardware        : MV-88fxx81
Revision        : 0000
Serial          : 0000000000000000

cat /proc/meminfo

MemTotal:       126236 kB
MemFree:         62112 kB
Buffers:           100 kB
Cached:          38176 kB
SwapCached:          0 kB
Active:          33444 kB
Inactive:        19396 kB
HighTotal:           0 kB
HighFree:            0 kB
LowTotal:       126236 kB
LowFree:         62112 kB
SwapTotal:     1003896 kB
SwapFree:      1003896 kB
Dirty:              36 kB
Writeback:           0 kB
Mapped:          21212 kB
Slab:             7928 kB
CommitLimit:   1067012 kB
Committed_AS:   172968 kB
PageTables:        696 kB
VmallocTotal:   385024 kB
VmallocUsed:      1040 kB
VmallocChunk:   383984 kB

cat /proc/interrupts

           CPU0
  0:       9197   Mv Timer Tick
  3:        351   serial
 21:         45   eth0
 29:       1180   mvSata
 47:          0   FuncSw
Err:          0

lsmod

Module                  Size  Used by
appletalk              38544  0
psnap                   4516  1 appletalk
llc                     8372  1 psnap
usblp                  14784  0
usb_storage            59975  0
ehci_marvell_hcd       33480  0
usbcore               127240  4 usblp,usb_storage,ehci_marvell_hcd

cat /proc/buffalo/firmware

SERIES=LinkStation
PRODUCTNAME=LS-WSGL/R1(SUJIN)
VERSION=0.16
SUBVERSION=FLASH 0.00
PRODUCTID=0x00003002
BUILDDATE=2008/03/12 11:17:32
BOOTVER=1.13

mount

rootfs on / type rootfs (rw)
/dev/root on / type xfs (rw)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw)
/dev/ram1 on /mnt/ram type tmpfs (rw)
/dev/md0 on /boot type ext3 (rw,data=ordered)
usbfs on /proc/bus/usb type usbfs (rw)
/dev/md2 on /mnt/array1 type xfs (rw,noatime,sunit=128,swidth=256)

uname -r

2.6.16.16-arm1

cat /proc/cmdline

console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOT
VER=1.13

cat /proc/mtd

dev:    size   erasesize  name
mtd0: 00040000 00001000 "phys_mapped_flash"

Partitions:

root@LS-WSGLBA4:/proc# cat partitions
major minor  #blocks  name

   8     0  488386584 sda
   8     1    1004031 sda1
   8     2    5004247 sda2
   8     4          1 sda4
   8     5    1004031 sda5
   8     6  480480021 sda6
   8    16  488386584 sdb
   8    17    1004031 sdb1
   8    18    5004247 sdb2
   8    20          1 sdb4
   8    21    1004031 sdb5
   8    22  480480021 sdb6
  31     0        256 mtdblock0
   9     0    1003904 md0
   9    10    1003904 md10
   9     1    5004160 md1
   9     2  960959872 md2

ls /proc

1              1516           5941           buffalo        misc
1046           1566           600            bus            modules
1049           1567           601            cmdline        mounts
11             168            6012           cpu            mtd
1172           169            6017           cpuinfo        net
1173           1703           6018           crypto         partitions
1263           192            6674           devices        resource_dump
1303           2              6726           diskstats      scsi
1310           3              6770           dma_copy       self
1311           327            6774           driver         slabinfo
1312           38             6790           execdomains    stat
1319           39             6796           filesystems    swaps
1333           4              6812           fs             sys
1358           40             6824           interrupts     sysvipc
1367           41             6850           iomem          tty
1370           42             7918           ioports        uptime
1486           43             847            kallsyms       version
1487           44             8947           kmsg           vmstat
1499           45             909            loadavg        zoneinfo
1507           491            9655           locks
1510           494            9656           mdstat
1514           5              buddyinfo      meminfo

cat /proc/buffalo/enet

MAC=00:1D:73:4C:XX:XX
link=100Mbps
duplex=full
jumboframe=enable
mtu=1500
regster9 value=0x0300
mode.config=auto:slave
mode.actual=master
=== for debug ===


page=0 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
       0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
       0x6060 0x6c08 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
       0x0000 0x0000 0x0040 0x0000 0x0000 0x0000 0x0000 0x0000

page=1 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
       0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
       0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0001 0x0000
       0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000

page=2 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
       0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
       0x0288 0x0000 0x0000 0x0008 0x0000 0x1070 0x0002 0x0000
       0x4705 0x0044 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000

page=3 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
       0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
       0x0201 0x4401 0x4105 0x0073 0x0000 0x0000 0x0003 0x0000
       0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000

page=4 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
       0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
       0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0004 0x0000
       0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000

page=5 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
       0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
       0x80ff 0xa0ff 0x80ff 0x89ff 0x0000 0x2000 0x0005 0x0603
       0x0000 0x0104 0x0f12 0x0a0c 0x0006 0x0000 0x0000 0x0000

page=6 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
       0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
       0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0006 0x0000
       0x0000 0x0000 0x0010 0x0000 0x0000 0x0000 0x0000 0x0000

page=7 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
       0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
       0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0007 0x0000
       0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000

page=8 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
       0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
       0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0008 0x0000
       0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000

page=9 0x1140 0x796d 0x0141 0x0e11 0x01e1 0x45e1 0x0005 0x2801
       0x0000 0x0300 0x4000 0x0000 0x0000 0x0000 0x0000 0x3000
       0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0009 0x0000
       0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000

dmesg

Linux version 2.6.16.16-arm1 (root@I.You) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #316 Tue Jul 22 16:22:33 JST 2008
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 200000000, Tclk = 166664740


- Warning - This LSP release was tested only with U-Boot release 1.7.3 

Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 32768
  DMA zone: 32768 pages, LIFO batch:7
  DMA32 zone: 0 pages, LIFO batch:0
  Normal zone: 0 pages, LIFO batch:0
  HighMem zone: 0 pages, LIFO batch:0
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOTVER=1.13
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 110620KB available (2992K code, 553K data, 112K init)
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
NET: Registered protocol family 16
FLASH boardId = 19
Flash bankwidth 1, base ff800000, size 40000
BUFFALO LS_WSGL_R1 FLASH size 256[KB]

  Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_WSGL_R1

Detected Tclk 166664740 and SysClk 200000000
Marvell USB EHCI Host controller #0: c16f5e00
Marvell USB EHCI Host controller #1: c16f5c00
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
Done.
cesadev_init(c0011c44)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered (default)
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
  o Ethernet descriptors in DRAM
  o DRAM SW cache-coherency
  o Checksum offload enabled
  o Loading network interface ** egiga_init_module (0)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
** BUFFALO Disable Command Queuing Function [0 0] **
** BUFFALO Disable Command Queuing Function [0 1] **
  Vendor: Hitachi   Model: HTS545050KTA300   Rev: BKFO
  Type:   Direct-Access                      ANSI SCSI revision: 03
  Vendor: Hitachi   Model: HTS545050KTA300   Rev: BKFO
  Type:   Direct-Access                      ANSI SCSI revision: 03
Linux IAL (ERROR) : retry command host=0, bus=0 SCpnt = c1422ba0
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda4 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
Linux IAL (ERROR) : retry command host=1, bus=1 SCpnt = c1422ba0
SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb4 < sdb5 sdb6 >
sd 1:0:0:0: Attached scsi disk sdb
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
physmap flash device: 40000 at ff800000
CFI: Found no phys_mapped_flash device at location zero
>jedec_probe
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
mice: PS/2 mouse device common for all mice
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
mvGppValueSet: Err. An attempt to set output value to GPP 15 in input mode.
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
mvGppValueSet: Err. An attempt to set output value to GPP 2 in input mode.
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.0.02 installed.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
md: md10 stopped.
md: md1 stopped.
md: md0 stopped.
md: bind<sdb1>
md: bind<sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
md: md10 stopped.
md: bind<sdb5>
md: bind<sda5>
raid1: raid set md10 active with 2 out of 2 mirrors
md: md1 stopped.
md: bind<sdb2>
md: bind<sda2>
raid1: raid set md1 active with 2 out of 2 mirrors
XFS mounting filesystem md1
Ending clean XFS mount for filesystem: md1
XFS mounting filesystem md1
Ending clean XFS mount for filesystem: md1
VFS: Mounted root (xfs filesystem).
Trying to move old root to /initrd ... okay
Freeing init memory: 112K
Adding 1003896k swap on /dev/md10.  Priority:-1 extents:1 across:1003896k
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ehci_platform ehci_platform.4523: EHCI Platform Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Platform Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
eth0: link down
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
md: md2 stopped.
md: bind<sdb6>
md: bind<sda6>
md2: setting max_sectors to 128, segment boundary to 32767
raid0: looking at sda6
raid0:   comparing sda6(480479936) with sda6(480479936)
raid0:   END
raid0:   ==> UNIQUE
raid0: 1 zones
raid0: looking at sdb6
raid0:   comparing sdb6(480479936) with sda6(480479936)
raid0:   EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 960959872 blocks.
raid0 : conf->hash_spacing is 960959872 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 4 bytes for hash.
XFS mounting filesystem md2
Ending clean XFS mount for filesystem: md2
BuffaloSwPollingCheck> SW_POWER_ON
NET: Registered protocol family 5
eth0: change mtu 1500 (buffer-size 1520) to 9676 (buffer-size 9696)
eth0: link down
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>

df

Filesystem           1k-blocks      Used Available Use% Mounted on
/dev/md1               4993920    255660   4738260   5% /
/dev/ram1                15360       112     15248   1% /mnt/ram
/dev/md0                988088    116632    871456  12% /boot
/dev/md2             480348864      3268 480345596   0% /mnt/array1

mount

rootfs on / type rootfs (rw)
/dev/root on / type xfs (rw)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw)
/dev/ram1 on /mnt/ram type tmpfs (rw)
/dev/md0 on /boot type ext3 (rw,data=ordered)
usbfs on /proc/bus/usb type usbfs (rw)
/dev/md2 on /mnt/array1 type xfs (rw,noatime)

smartctl -a /dev/sda (same for second drive)

smartctl version 5.37 [armv5tejl-unknown-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     Hitachi HTS545050KTA300
Serial Number:    080227BK0F00VEG0H--A
Firmware Version: BKFOC60M
User Capacity:    500,107,862,016 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   8
ATA Standard is:  Not recognized. Minor revision code: 0x42
Local Time is:    Fri Jul 25 23:42:28 2008 JST
SMART support is: Available - device has SMART capability.
SMART support is: Disabled

SMART Disabled. Use option -s with argument 'on' to enable it.

smartctl -A /dev/sda (sync in progress, note temperature)

=== START OF READ SMART DATA SECTION ===
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   100   062    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0005   100   100   040    Pre-fail  Offline      -       0
  3 Spin_Up_Time            0x0007   236   236   033    Pre-fail  Always       -       1
  4 Start_Stop_Count        0x0012   100   100   000    Old_age   Always       -       14
  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   100   100   040    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0012   100   100   000    Old_age   Always       -       1
 10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       14
191 G-Sense_Error_Rate      0x000a   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       12
193 Load_Cycle_Count        0x0012   100   100   000    Old_age   Always       -       143
194 Temperature_Celsius     0x0002   096   096   000    Old_age   Always       -       57 (Lifetime Min/Max 25/57)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0
223 Load_Retry_Count        0x000a   100   100   000    Old_age   Always       -       0

reboot procedure

Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0)
 <0>Rebooting in 90 seconds..
BuffaloChangePowerStatusBeforeHalt > Check power status. MagicKey = 24
BuffaloChangePowerStatusBeforeHalt > Changed to 43 from 24