Difference between revisions of "Recover a non working "bricked" Linkstation"

From NAS-Central Buffalo - The Linkstation Wiki
Jump to: navigation, search
m (Reconnect disk to LS and flash firmware)
m (Reconnect disk to LS and flash firmware)
Line 47: Line 47:
 
*Open the archive and carefully read the included <tt>README</tt> file for any specific instructions.
 
*Open the archive and carefully read the included <tt>README</tt> file for any specific instructions.
 
*Disable any firewall(s), '''including any built-in Windows firewall'''  
 
*Disable any firewall(s), '''including any built-in Windows firewall'''  
*Make sure the LinkStation and your PC are on the same sub-network. This likely requires that you change the IP address (and probably the subnet-mask) of your PC and router to a different IP address in [[EM Mode]] it will have a static IP address of 192.168.11.150
+
*Make sure the LinkStation and your PC are on the same sub-network. This likely requires that you change the IP address (and probably the subnet-mask) of your PC and router to a different IP address in [[EM Mode]] it will have a static IP address of 192.168.11.150 or to connect your PC and LinkStation directly with a crossover cable.
 
*unpack HD-H*.zip (use the proper firmware for your LS)
 
*unpack HD-H*.zip (use the proper firmware for your LS)
 
*start HD-H*FWUpdate.exe (use the proper updater for your LS)
 
*start HD-H*FWUpdate.exe (use the proper updater for your LS)

Revision as of 06:19, 10 October 2006

Any information how to recover a non working, bricked Linkstation should get here.

Upgrade hard drive
Bar.png
This is generally accepted as the easier way to upgrade your Linkstation's hard drive. Just put your new hard drive in and start at the Reconnect disk to LS and flash firmware section. The other more involved way is to recreate the filesystem yourself on a workstation, this method is described in this article:Upgrade (or replace) the existing LinkStation hard drive


Contents

Firmware Reinstallation

The following steps can be used to "reanimate" a Linkstation:

Open LinkStation

(see Disassemble the LinkStation)

  • disconnect disk from internal mainboard and power.

Remove all partitions

  • connect disk to a PC with knoppix via a USB-IDE adapter or directly to the IDE controller. If you change the IDE setting on your hard drive to match it to a "Slave" setting, remember to put the jumper back to "Master" before connecting back the hard drive to the Linkstation
  • start knoppix in terminal mode "knoppix 2"

For a USB-IDE connection:

parted /dev/sda

For IDE direct connection:
hda = Primary Master hdb = Primary Slave hdc = Secondary Master hdd = Secondary Slave

So if you used Primary Master you would type:

parted /dev/hda

After this, the commands are the same for USB & IDE direct:

rm 1
rm 2
rm 3
rm 4
quit
  • (optional) For Windows users who do not wish to become familiar with Knoppix, Google and get "Explore2fs". When the LS drive is connected to the IDE controller on your pc, this application may allow you to retrieve data from the LS disk and copy (export) it to your Windows drive. You can then use Windows Computer Management --> Disk Management to delete the partitions on the LS drive and continue with the directions as posted here.

Reconnect disk to LS and flash firmware

  • power on LS (Reset button not pressed)
  • Flash The The LinkStation firmware flasher
  • Open the archive and carefully read the included README file for any specific instructions.
  • Disable any firewall(s), including any built-in Windows firewall
  • Make sure the LinkStation and your PC are on the same sub-network. This likely requires that you change the IP address (and probably the subnet-mask) of your PC and router to a different IP address in EM Mode it will have a static IP address of 192.168.11.150 or to connect your PC and LinkStation directly with a crossover cable.
  • unpack HD-H*.zip (use the proper firmware for your LS)
  • start HD-H*FWUpdate.exe (use the proper updater for your LS)
GeneralFreeLink1.jpg
  • press "search", should find Linkstation "EM" (Emergency Mode)
  • After finding your LinkStation, press the "Renew Firmware" button, and wait. Have patience, and keep your calm. If you think the Firmware updater is acting strange, do not try to disconnect the LinkStation or abort the update in another way.
  • start update, following messages appear:
Settings are being saved
Firmware is being transmitted
LinkStation Firmware has been renewed
Settings are being restored
  • if You get the following message You are done.
The firmware has been renewed
  • But because the reformatting (?)and partitioning takes too long,

the diskfill LED may blink and you may get:

Attempt to renew firmware has failed
  • if so, wait until Diskfull LED goes off after some minutes.
  • press "search" again.
  • start update again.
  • after all the other messages You should get this time:
The firmware has been renewed
  • After flashing connect your LinkStation up to the network with subnet 192.168.1.XXX the LS is now reachable via telnet and the "old" IP. so switch back IP settings and reenable the windows firewall.
    • Find your LinkStation on the network and Telnet to it with PuTTYtel You will be at the root shell.

Login to the LinkStation

  • use telnet to get a prompt:
telnet linkstation
  • set root password:
passwd
  • change bash to login:
vi /etc/init.d/telnet
  • add a new guest user
useradd -m -d /home/guest guest
  • and ...
reboot
Link.png This article is currently a stub. You can help this Wiki by expanding it

. This template will categorize articles that include it into Category:Stubs.