SCON-KIT/ PRO quick manual
From NAS-Central Buffalo - The Linkstation Wiki
(Difference between revisions)
m (→Directions) |
m |
||
| Line 8: | Line 8: | ||
HELP ME! BBS | HELP ME! BBS | ||
http://kuroutoshikou.com/modules/kurobbs/?iid=992 | http://kuroutoshikou.com/modules/kurobbs/?iid=992 | ||
| + | |||
| + | [[Image:scionusb.jpg|300px]] | ||
| + | |||
| + | |||
| + | {| | ||
| + | |USB Type A || <--> || USB board FTDI FT232RL || ---TXD--><br><--RXD--- || Cable || ---TXD--><br><--RXD--- || KuroBox Pro Daughterboard | ||
| + | |} | ||
| Line 44: | Line 51: | ||
|} | |} | ||
| - | [[Image:kuroprodaughterboard|300px|kurobox pro daughterboard]] | + | [[Image:kuroprodaughterboard.jpg|300px|kurobox pro daughterboard]] |
| + | |||
| + | [[Image:kuroproduartpinout.jpg|300px]] | ||
==Directions== | ==Directions== | ||
| Line 57: | Line 66: | ||
* Open front panel of KURO-BOX/PRO, take the HDD daughter board out. | * Open front panel of KURO-BOX/PRO, take the HDD daughter board out. | ||
* Put the serial header onto UART0. make sure pin No.1 match to TXD. | * Put the serial header onto UART0. make sure pin No.1 match to TXD. | ||
| + | [[Image:kuroproplaceheader.jpg|300px]] | ||
| + | |||
* Attach with a soldering iron from the back of the base. | * Attach with a soldering iron from the back of the base. | ||
| + | [[Image:kuroprosolderheader.jpg|300px]] | ||
* Put the daughterboard back onto the KURO-BOX/PRO | * Put the daughterboard back onto the KURO-BOX/PRO | ||
====Connection of SCON-KIT/PRO==== | ====Connection of SCON-KIT/PRO==== | ||
* Connect SCON-KIT/PRO and UART0 on the sub base of KURO-BOX/PRO by using a patch cord | * Connect SCON-KIT/PRO and UART0 on the sub base of KURO-BOX/PRO by using a patch cord | ||
| + | [[Image:kuroprowireport.jpg|300px]] | ||
* Do not connect to the PC yet. | * Do not connect to the PC yet. | ||
====Preparation of appropriate COM port driver and install==== | ====Preparation of appropriate COM port driver and install==== | ||
Revision as of 04:26, 19 July 2007
Contents |
Introduction
- SCON-KIT/PRO is a serial console connection kit for KURO/BOX/PRO
- You will need a SOLDERING IRON for this kit
- The chance of guarantee is only for the first time when it does not work
- The term of guarantee depends on the store
- No repair or support service for this kit
- Help page for this product:
HELP ME! BBS http://kuroutoshikou.com/modules/kurobbs/?iid=992
| USB Type A | <--> | USB board FTDI FT232RL | ---TXD--> <--RXD--- | Cable | ---TXD--> <--RXD--- | KuroBox Pro Daughterboard |
| IC | FDI FT232RL |
| Kuro-Box/Pro Interface | 3.3V TTL |
| PC Interface | USB 1.1 |
Scion Kit Pinout
| 1 | TXD | Out |
| 2 | RXD | In |
| 3 | VCC | In |
| 4 | GND | - |
KuroBox Pro UART0 Pinout
| 1 | TXD | Out |
| 2 | RXD | In |
| 3 | VCC (+3.3V) | Out |
| 4 | GND | - |
Directions
- Do not insert/extract or push/pull attached connector frequently
- Do not put stress on connector and base
- Do not attach connector when the power of KURO-BOX/PRO is on
- You will need terminal software
Setup Process
Attach Serial Header to circuit board by soldering iron make sure the AC plug is off.
- Open front panel of KURO-BOX/PRO, take the HDD daughter board out.
- Put the serial header onto UART0. make sure pin No.1 match to TXD.
- Attach with a soldering iron from the back of the base.
- Put the daughterboard back onto the KURO-BOX/PRO
Connection of SCON-KIT/PRO
- Connect SCON-KIT/PRO and UART0 on the sub base of KURO-BOX/PRO by using a patch cord
- Do not connect to the PC yet.
Preparation of appropriate COM port driver and install
- download the appropriate COM port driver for FT232R from the URL below
http://www.ftdichip.com/Drivers/VCP.htm
- Connect the SCON-KIT/PRO to the USB port of PC. Install the driver which you downloaded.
- Open Device manager and check which COM port is used. For example in the picture, port is named COM5.
Set up the terminal software
- Start terminal software. See KURO-BOX/PRO UART specification set up serial port. Use your COM? port for setting.
Example: the way to setup using “HyperTerminal” in WindowsXP/2000
- start “hyper terminal” and register a name of the new connection
- connection method: chose COM? which you checked before
- see KURO-BOX/ PRO UART specification and set up the port
- you can see he picture when you start KURO-BOX/PRO
| Note |
|
| sometimes, you may get the junk/Trash data when you turn the power on/off or reboot, but it is not abnormal. If you cannot return, reset the terminal software or reconnect. |
