Difference between revisions of "SCON-KIT/ PRO quick manual"

From NAS-Central Buffalo - The Linkstation Wiki
Jump to: navigation, search
m
m
Line 1: Line 1:
 
{{Articles|Kurobox|Hardware}}
 
{{Articles|Kurobox|Hardware}}
 +
[[Image:scionusb.jpg|300px|right]]
 
==Introduction==
 
==Introduction==
 
* SCON-KIT/PRO is a serial console connection kit for KURO/BOX/PRO
 
* SCON-KIT/PRO is a serial console connection kit for KURO/BOX/PRO
Line 9: Line 10:
 
  HELP ME! BBS
 
  HELP ME! BBS
 
  http://kuroutoshikou.com/modules/kurobbs/?iid=992
 
  http://kuroutoshikou.com/modules/kurobbs/?iid=992
 
[[Image:scionusb.jpg|300px]]
 
 
  
 
{|
 
{|
Line 92: Line 90:
 
  {{Postit|Note|sometimes, you may get the junk/Trash data when you turn the power on/off or reboot, but it is not abnormal. If you cannot return, reset the terminal software or reconnect.}}
 
  {{Postit|Note|sometimes, you may get the junk/Trash data when you turn the power on/off or reboot, but it is not abnormal. If you cannot return, reset the terminal software or reconnect.}}
 
[[Image:kuroprologin.jpg|400px]]
 
[[Image:kuroprologin.jpg|400px]]
 +
 +
==References==
 +
* [http://kuroutoshikou.com/products/scon-kit_pro/scon-kit_pro_quickmanual.pdf PDF of SCION USB serial access kit]

Revision as of 04:36, 19 July 2007

Scionusb.jpg

Contents

Introduction

  • SCON-KIT/PRO is a serial console connection kit for KURO/BOX/PRO
  • You will need a SOLDERING IRON for this kit
  • The chance of guarantee is only for the first time when it does not work
  • The term of guarantee depends on the store
  • No repair or support service for this kit
  • Help page for this product:
HELP ME! BBS
http://kuroutoshikou.com/modules/kurobbs/?iid=992
USB Type A <--> USB board FTDI FT232RL ---TXD-->
<--RXD---
Cable ---TXD-->
<--RXD---
KuroBox Pro Daughterboard


IC FDI FT232RL
Kuro-Box/Pro Interface 3.3V TTL
PC Interface USB 1.1


Scion Kit Pinout

1 TXD Out
2 RXD In
3 VCC In
4 GND -


KuroBox Pro UART0 Pinout

1 TXD Out
2 RXD In
3 VCC (+3.3V) Out
4 GND -

kurobox pro daughterboard

Kuroproduartpinout.jpg

Directions

  • Do not insert/extract or push/pull attached connector frequently
  • Do not put stress on connector and base
  • Do not attach connector when the power of KURO-BOX/PRO is on
  • You will need terminal software


Setup Process

Attach Serial Header to circuit board by soldering iron make sure the AC plug is off.

  • Open front panel of KURO-BOX/PRO, take the HDD daughter board out.
  • Put the serial header onto UART0. make sure pin No.1 match to TXD.

Kuroproplaceheader.jpg

  • Attach with a soldering iron from the back of the base.

Kuroprosolderheader.jpg

  • Put the daughterboard back onto the KURO-BOX/PRO

Connection of SCON-KIT/PRO

  • Connect SCON-KIT/PRO and UART0 on the sub base of KURO-BOX/PRO by using a patch cord

Kuroprowireport.jpg

  • Do not connect to the PC yet.

Preparation of appropriate COM port driver and install

  • download the appropriate COM port driver for FT232R from the URL below
    http://www.ftdichip.com/Drivers/VCP.htm
  • Connect the SCON-KIT/PRO to the USB port of PC. Install the driver which you downloaded.
  • Open Device manager and check which COM port is used. For example in the picture, port is named COM5.

Set up the terminal software

  • Start terminal software. See KURO-BOX/PRO UART specification set up serial port. Use your COM? port for setting.

Example: the way to setup using “HyperTerminal” in WindowsXP/2000

    • start “hyper terminal” and register a name of the new connection
    • connection method: chose COM? which you checked before
    • see KURO-BOX/ PRO UART specification and set up the port
    • you can see he picture when you start KURO-BOX/PRO


Note
Bar.png
sometimes, you may get the junk/Trash data when you turn the power on/off or reboot, but it is not abnormal. If you cannot return, reset the terminal software or reconnect.


Kuroprologin.jpg

References