Difference between revisions of "SCON-KIT/ PRO quick manual"

From NAS-Central Buffalo - The Linkstation Wiki
Jump to: navigation, search
m
m (Connection of SCON-KIT/PRO)
 
(41 intermediate revisions by one user not shown)
Line 1: Line 1:
{{Articles|Kurobox|Hardware}}
+
{{Articles|Kurobox|Hardware|KuroboxPro}}
==Introduction==
+
[[Image:scion-kit-pro.jpg|right]]
 +
=Introduction=
 +
==Japan==
 
* SCON-KIT/PRO is a serial console connection kit for KURO/BOX/PRO
 
* SCON-KIT/PRO is a serial console connection kit for KURO/BOX/PRO
* You will need a SOLDERING IRON for this kit
+
* You will need a [[w:Soldering iron|SOLDERING IRON]] for this kit
* The chance of guarantee is only for the first time when it does not work
+
* The chance of a guarantee for refund is only for the first time when it does not work
* The term of guarantee depends on the store
+
* The terms of the guarantee depend on the store you bought the kit from
* No repair or support service for this kit
+
* No repair or support service for this kit is available
* Help page for this product:  
+
* The help page for this product is at:  
 
  HELP ME! BBS
 
  HELP ME! BBS
 
  http://kuroutoshikou.com/modules/kurobbs/?iid=992
 
  http://kuroutoshikou.com/modules/kurobbs/?iid=992
  
[[Image:scionusb.jpg|300px]]
+
{| border =0
 
+
|bgcolor="grey"|<b>USB Type A</b> || <-->  
 
+
|bgcolor="grey"|<b> USB board FTDI FT232RL</b> || ---TXD--><br><--RXD---  
{|
+
|bgcolor="grey"|<b> Cable</b> || ---TXD--><br><--RXD---  
|USB Type A || <--> || USB board FTDI FT232RL || ---TXD--><br><--RXD--- || Cable || ---TXD--><br><--RXD--- || KuroBox Pro Daughterboard
+
|bgcolor="grey"|<b> KuroBox Pro Daughterboard</b>
 +
|-
 +
|colspan=7 align="center"|[[Image:scionusb.jpg]]
 
|}
 
|}
  
 +
{| cellpadding=20
  
 +
|
  
{| border=1
+
{| class="wikitable"
|<b>IC</b> || <b>FDI FT232RL</b>
+
! |<b>IC</b>  
 +
! |<b>FDI FT232RL</b>
 
|-
 
|-
 
|Kuro-Box/Pro Interface || 3.3V TTL
 
|Kuro-Box/Pro Interface || 3.3V TTL
Line 27: Line 34:
 
|}
 
|}
  
 
+
||
Scion Kit Pinout
+
<b>Scon Kit Pinout</b>
{| border=1
+
{| class="wikitable"
 
|1 || TXD || Out
 
|1 || TXD || Out
 
|-
 
|-
Line 39: Line 46:
 
|}
 
|}
  
 +
||
  
 
+
<b>KuroBox Pro UART0  Pinout</b>
KuroBox Pro UART0  Pinout
+
{| class="wikitable"
{| border=1
+
 
|1 || TXD || Out
 
|1 || TXD || Out
 
|-
 
|-
Line 52: Line 59:
 
|}
 
|}
  
[[Image:kuroprodaughterboard.jpg|300px|kurobox pro daughterboard]]
+
|}
 +
 
 +
==US/Europe==
 +
The SCON-KIT would be very difficult to get in the US/Europe. You would likely have to use a different Serial Converter
  
[[Image:kuroproduartpinout.jpg|300px]]
+
{{Level Shifter}}
  
==Directions==
+
=Attach a Serial Header to the Daughterboard=
 
* Do not insert/extract or push/pull attached connector frequently
 
* Do not insert/extract or push/pull attached connector frequently
 
* Do not put stress on connector and base
 
* Do not put stress on connector and base
Line 62: Line 72:
 
* You will need terminal software  
 
* You will need terminal software  
  
 
+
===Attach Serial Header to circuit board by soldering iron make sure the AC plug is off.===
===Setup Process===
+
====Attach Serial Header to circuit board by soldering iron make sure the AC plug is off.====
+
 
* Open front panel of KURO-BOX/PRO, take the HDD daughter board out.
 
* Open front panel of KURO-BOX/PRO, take the HDD daughter board out.
* Put the serial header onto UART0. make sure pin No.1 match to TXD.
 
[[Image:kuroproplaceheader.jpg|300px]]
 
  
 +
[[Image:kuroprodaughterboard.jpg|400px|kurobox pro daughterboard]]
 +
 +
* Put the serial header onto UART0.
 +
[[Image:kuroproduartpinout.jpg]]
 +
* Make sure that pin No.1 matches to TXD.
 +
[[Image:kuroproplaceheader.jpg]]
 
* Attach with a soldering iron from the back of the base.
 
* Attach with a soldering iron from the back of the base.
[[Image:kuroprosolderheader.jpg|300px]]
+
[[Image:kuroprosolderheader.jpg]]
 
* Put the daughterboard back onto the KURO-BOX/PRO
 
* Put the daughterboard back onto the KURO-BOX/PRO
====Connection of SCON-KIT/PRO====
+
 
* Connect SCON-KIT/PRO and UART0 on the sub base of KURO-BOX/PRO by using a patch cord
+
=Use the SCON-KIT as a USB/TTL converter=
 +
===Connection of SCON-KIT/PRO===
 +
* Connect SCON-KIT/PRO and UART0 on the sub base of KURO-BOX/PRO by using the patch cord
 
[[Image:kuroprowireport.jpg|300px]]
 
[[Image:kuroprowireport.jpg|300px]]
 
* Do not connect to the PC yet.
 
* Do not connect to the PC yet.
====Preparation of appropriate COM port driver and install====
+
 
* download the appropriate COM port driver for FT232R from the URL below
+
===Get the appropriate COM port driver and install===
 +
* Download the appropriate COM port driver for FT232R from the URL below
 
     http://www.ftdichip.com/Drivers/VCP.htm
 
     http://www.ftdichip.com/Drivers/VCP.htm
 
* Connect the  SCON-KIT/PRO to the USB port of PC. Install the driver which you downloaded.  
 
* Connect the  SCON-KIT/PRO to the USB port of PC. Install the driver which you downloaded.  
* Open Device manager and check which COM port is used. For example in the picture, port is named COM5.
+
* Open Device manager and check which COM port is used.
====Set up the terminal software====
+
* Start terminal software. See KURO-BOX/PRO UART specification set up serial port. Use your COM? port for setting.
+
  
===Example: the way to setup using “HyperTerminal” in WindowsXP/2000===
+
===Set up the terminal software===
**  start “hyper terminal” and register a name of the new connection
+
 
*connection method: chose COM? which you checked before
+
* Start terminal software.  Use your COM port. Use the following for serial port settings:
*see KURO-BOX/ PRO UART specification and set up the port
+
====KURO-BOX/PRO UART Specifications====
*you can see he picture when you start KURO-BOX/PRO
+
{| class="wikitable"
 +
|-
 +
! |Data
 +
! |Settings
 +
|-
 +
|Baudrate ||115200
 +
|-
 +
|Data bits ||8
 +
|-
 +
|Parity ||None
 +
|-
 +
|Stop bits ||1 
 +
|-
 +
|Flow Control ||None
 +
|}
 +
 
 +
==Example: the way to setup using “HyperTerminal” in WindowsXP/2000==
 +
{{Postit|Other OS/Terminal Emulators|
 +
* Windows:  [[w:PuTTY|PuTTY]]
 +
* Linux:    [[w:Gtkterm|gtkterm]], [[w:Minicom|Minicom]]
 +
* OSX:      [[w:Zterm|Zterm]]
 +
}}
 +
Start “[[w:HyperACCESS|HyperTerminal]]” and register a name for the new connection
 +
[[Image:Hyperterminal-conndesc.JPG|200px]]
 +
Connection method: the COM port which you checked before (in this case COM5)
 +
[[Image:Hyperterminal-comm.JPG|200px]]
 +
See [[#KURO-BOX/PRO UART Specifications |KURO-BOX/ PRO UART specification]] and set up the port
 +
[[Image:Hyperterminal-portsett.JPG|200px]]
 +
You should see the output in this picture when you start the KURO-BOX/PRO
 +
{| width=100%
 +
|-
 +
||[[Image:kuroprologin.jpg]]
 +
|| {{Postit|Note|Sometimes, you may get the junk/Trash data when you turn the power on/off or reboot, but this is not abnormal. If you cannot return to normal output, reset the terminal software or reconnect.}}
 +
|}
  
{{Postit|Note|sometimes, you may get the junk/Trash data when you turn the power on/off or reboot, but it is not abnormal. If you cannot return, reset the terminal software or reconnect.}}
+
[[Kurobox Pro UBoot/Linux Console Message - bootup]]
[[Image:kuroprologin.jpg|400px]]
+
=References=
 +
* [http://kuroutoshikou.com/products/scon-kit_pro/scon-kit_pro_quickmanual.pdf PDF of SCON USB serial access kit]

Latest revision as of 00:36, 15 August 2008

Scion-kit-pro.jpg

Contents

Introduction

Japan

  • SCON-KIT/PRO is a serial console connection kit for KURO/BOX/PRO
  • You will need a SOLDERING IRON for this kit
  • The chance of a guarantee for refund is only for the first time when it does not work
  • The terms of the guarantee depend on the store you bought the kit from
  • No repair or support service for this kit is available
  • The help page for this product is at:
HELP ME! BBS
http://kuroutoshikou.com/modules/kurobbs/?iid=992
USB Type A <--> USB board FTDI FT232RL ---TXD-->
<--RXD---
Cable ---TXD-->
<--RXD---
KuroBox Pro Daughterboard
Scionusb.jpg
IC FDI FT232RL
Kuro-Box/Pro Interface 3.3V TTL
PC Interface USB 1.1

Scon Kit Pinout

1 TXD Out
2 RXD In
3 VCC In
4 GND -

KuroBox Pro UART0 Pinout

1 TXD Out
2 RXD In
3 VCC (+3.3V) Out
4 GND -

US/Europe

The SCON-KIT would be very difficult to get in the US/Europe. You would likely have to use a different Serial Converter

The serial port signals from the processor are only 3.3V. For proper RS-232 12V signaling, an RS-232 level shifter needs to be added. These are very common in PDA serial cables also, but can be purchased

Models other than KuroPro
Bar.png

If you are attaching a serial header pin onto the main board, you may want to consider:

  • Using the header pin unit with a 90 degree bend, or you might not be able to close the case
  • Soldering it with the pins toward the interior, rather than toward the case. This allows easier access, since if the pins face the case side they would be very close to the metal side. This would make access is so tight that one might end up taking the board out to get plug fitted on the pins.


Build your own LVTTL/RS232 or LVTTL/USB interface

Buy your own TTL Level Shifter

Usage considerations for the TTL-232R-3V3

TTL-232R-3V3 USB to TTL Serial Converter Cable
A very similar TTL/USB converter cable that uses a chip by FTDI (the same chip is used in the SCON-KIT ) can be obtained, but the pinout at the connector end would need to be reassigned: Spec Sheet w/ pinout, wire colors & other info
MM232R.jpg Mouser Part # 895-TTL-232R-3V3 $20.00
4pinheader.gif Mouser Part # 517-929400-01-04 $0.32

A working/tested pinout/wire-color scheme is:

Color Pin Number Signal
yellow 1 TXD
orange 2 RXD
unused 3 VCC
black 4 GND
  • Solder the 4-pin header to the board. Make sure you don't have shorts.
  • You will need to switch wires on the TTL-232R-3V3 cable. Use a sharp object to lift the plastic tabs and carefully pull the wires out. Rearrange them according to the table above (black, empty, orange, yellow, empty, empty) and slide those wires back in. Tape the other wires to make sure they don't short anything.
  • When plugging in the cable, make sure black aligns with GND, yellow with TXD, and orange with RXD.
  • Connect the USB cable to your computer, start a terminal program with the right settings.
  • Turn on the device, you should see output from the bootloader in couple seconds.

Attach a Serial Header to the Daughterboard

  • Do not insert/extract or push/pull attached connector frequently
  • Do not put stress on connector and base
  • Do not attach connector when the power of KURO-BOX/PRO is on
  • You will need terminal software

Attach Serial Header to circuit board by soldering iron make sure the AC plug is off.

  • Open front panel of KURO-BOX/PRO, take the HDD daughter board out.

kurobox pro daughterboard

  • Put the serial header onto UART0.

Kuroproduartpinout.jpg

  • Make sure that pin No.1 matches to TXD.

Kuroproplaceheader.jpg

  • Attach with a soldering iron from the back of the base.

Kuroprosolderheader.jpg

  • Put the daughterboard back onto the KURO-BOX/PRO

Use the SCON-KIT as a USB/TTL converter

Connection of SCON-KIT/PRO

  • Connect SCON-KIT/PRO and UART0 on the sub base of KURO-BOX/PRO by using the patch cord

Kuroprowireport.jpg

  • Do not connect to the PC yet.

Get the appropriate COM port driver and install

  • Download the appropriate COM port driver for FT232R from the URL below
    http://www.ftdichip.com/Drivers/VCP.htm
  • Connect the SCON-KIT/PRO to the USB port of PC. Install the driver which you downloaded.
  • Open Device manager and check which COM port is used.

Set up the terminal software

  • Start terminal software. Use your COM port. Use the following for serial port settings:

KURO-BOX/PRO UART Specifications

Data Settings
Baudrate 115200
Data bits 8
Parity None
Stop bits 1
Flow Control None

Example: the way to setup using “HyperTerminal” in WindowsXP/2000

Other OS/Terminal Emulators
Bar.png


  • Start “HyperTerminal” and register a name for the new connection

Hyperterminal-conndesc.JPG

  • Connection method: the COM port which you checked before (in this case COM5)

Hyperterminal-comm.JPG

Hyperterminal-portsett.JPG

  • You should see the output in this picture when you start the KURO-BOX/PRO
Kuroprologin.jpg
Note
Bar.png
Sometimes, you may get the junk/Trash data when you turn the power on/off or reboot, but this is not abnormal. If you cannot return to normal output, reset the terminal software or reconnect.


Kurobox Pro UBoot/Linux Console Message - bootup

References