Serial console TsP - Revision history

Tsmike at 19:44, 30 March 2013

Tsmike — Sat, 30 Mar 2013 19:44:52 GMT

← Older revision		Revision as of 19:44, 30 March 2013
Line 11:		Line 11:
	* Open your browser, and open this page : http://{TeraStation_Pro_IP}/cgi-bin/task.cgi?task=console&param=on*		* Open your browser, and open this page : http://{TeraStation_Pro_IP}/cgi-bin/task.cgi?task=console&param=on*
	TSmike 2013-03-30: You may need to enter your username and password using the "uuu=" and "ppp=" parameters		TSmike 2013-03-30: You may need to enter your username and password using the "uuu=" and "ppp=" parameters
-	http://{TeraStation_Pro_IP}/cgi-bin/task.cgi?uuu=admin&ppp=password&task=console&param=on	+	http://{TeraStation_Pro_IP}/cgi-bin/task.cgi?uuu=admin&ppp=password&task=console&param=on
		+	otherwise you may see
		+	task:auth_fail - param:auth_fail

	* Log in telnet/SSH and run this command : /usr/sbin/miconapl -a serialmode_console		* Log in telnet/SSH and run this command : /usr/sbin/miconapl -a serialmode_console

Tsmike at 19:43, 30 March 2013

Tsmike — Sat, 30 Mar 2013 19:43:10 GMT

← Older revision		Revision as of 19:43, 30 March 2013
Line 10:		Line 10:
	There are 2 methods to switch the serial link to console mode :		There are 2 methods to switch the serial link to console mode :
	* Open your browser, and open this page : http://{TeraStation_Pro_IP}/cgi-bin/task.cgi?task=console&param=on*		* Open your browser, and open this page : http://{TeraStation_Pro_IP}/cgi-bin/task.cgi?task=console&param=on*
		+	TSmike 2013-03-30: You may need to enter your username and password using the "uuu=" and "ppp=" parameters
		+	http://{TeraStation_Pro_IP}/cgi-bin/task.cgi?uuu=admin&ppp=password&task=console&param=on
		+
	* Log in telnet/SSH and run this command : /usr/sbin/miconapl -a serialmode_console		* Log in telnet/SSH and run this command : /usr/sbin/miconapl -a serialmode_console
	Once the switching is done, you can reboot your TsP (A power-off will reset the serial switchin to UPS function, but a reboot will keep the setting as defined by the user). You'll then be able to see console output using HyperTerminal application.		Once the switching is done, you can reboot your TsP (A power-off will reset the serial switchin to UPS function, but a reboot will keep the setting as defined by the user). You'll then be able to see console output using HyperTerminal application.

Entropy: /* How to get a serial console log on the TsP */

Entropy — Tue, 13 Nov 2012 06:26:39 GMT

How to get a serial console log on the TsP

← Older revision		Revision as of 06:26, 13 November 2012
Line 17:		Line 17:
	You'll also need to connect your computer to the TsP using a cross over serial cable.		You'll also need to connect your computer to the TsP using a cross over serial cable.

-	'''Note:''' This also works on the TSP2.	+	'''Note:''' This also works on the TSP2, except the serial port should be set to 115200 bps, 8 bit, 1 stop bit, no parity, no flow control.

	== Console output ==		== Console output ==

Entropy: /* How to get a serial console log on the TsP */

Entropy — Tue, 13 Nov 2012 06:25:40 GMT

How to get a serial console log on the TsP

← Older revision		Revision as of 06:25, 13 November 2012
Line 17:		Line 17:
	You'll also need to connect your computer to the TsP using a cross over serial cable.		You'll also need to connect your computer to the TsP using a cross over serial cable.

-	'''Note:''' This ~~might not work~~ on the TSP2.	+	'''Note:''' This also works on the TSP2.
-		+
	== Console output ==		== Console output ==
	Here are some console output logs :		Here are some console output logs :

Ramuk at 05:56, 8 September 2008

Ramuk — Mon, 08 Sep 2008 05:56:54 GMT

← Older revision		Revision as of 05:56, 8 September 2008
Line 1:		Line 1:
	{{Template:Articles\|TerastationProV1}}		{{Template:Articles\|TerastationProV1}}
-		+	[[Image:Ts-pro-1.jpg\|frame\|right]]
		+	__TOC__
	== What is the Serial Console ==		== What is the Serial Console ==
	The serial console is allowing to get message output from the boot process. You can check the boot log (you can even interrupt it to enter some commands), and also the kernel boot log.		The serial console is allowing to get message output from the boot process. You can check the boot log (you can even interrupt it to enter some commands), and also the kernel boot log.

EnTerr: Revert to before spam

EnTerr — Wed, 19 Dec 2007 09:19:09 GMT

Revert to before spam

← Older revision		Revision as of 09:19, 19 December 2007
Line 8:		Line 8:
	Many Bufalo's devices need some soldering work to get the console output over the serial link, the good news with the TeraStation Pro is that you don't even need to open the box to get serial console access because you can use the UPS serial port ! The "bad" news is that you need to start the TsP at least one time to switch the serial link from ''UPS function'' to ''serial function''.		Many Bufalo's devices need some soldering work to get the console output over the serial link, the good news with the TeraStation Pro is that you don't even need to open the box to get serial console access because you can use the UPS serial port ! The "bad" news is that you need to start the TsP at least one time to switch the serial link from ''UPS function'' to ''serial function''.
	There are 2 methods to switch the serial link to console mode :		There are 2 methods to switch the serial link to console mode :
-	* Open your browser, and open this page : http://{TeraStation_Pro_IP}/cgi-bin/task.cgi?task=console	+	* Open your browser, and open this page : http://{TeraStation_Pro_IP}/cgi-bin/task.cgi?task=console&param=on*
		+	* Log in telnet/SSH and run this command : /usr/sbin/miconapl -a serialmode_console
		+	Once the switching is done, you can reboot your TsP (A power-off will reset the serial switchin to UPS function, but a reboot will keep the setting as defined by the user). You'll then be able to see console output using HyperTerminal application.
		+
		+	The serial port configuration is the following :
		+	57600bps, 8bit, 1 stop bit, no parity, no flow control
		+	You'll also need to connect your computer to the TsP using a cross over serial cable.
		+
		+	'''Note:''' This might not work on the TSP2.
		+
		+	== Console output ==
		+	Here are some console output logs :
		+	* The bootloader
		+	BOOTCODE 1.24 (Jul 6 2006 - 15:30:34)
		+	romsum=0b521f8f Setup MMU
		+	Memtest64bit
		+	MemtestData
		+	aaaaaaaa 55555555 ffffffff 00000000 MemtestAdrs
		+	isUseRevClock=0
		+	idsel=11:816910ec
		+	idsel=12:35121095
		+	idsel=13:35121095
		+	idsel=14:00351033
		+
		+	***** Product Information *****
		+	----------------------------------
		+	Product Name: TS-TGL(IENARI)
		+	VER: 3.09
		+	Date: 2006/7/18 9:29:29
		+	----------------------------------
		+	Firmware check:done.
		+
		+	>>root=/dev/md0
		+	hit any key to Enter cmd mode.
		+	Now Loading...zimage_start=FFC0006C
		+	zimage_size=000FD3BD
		+	done.
		+	Now Booting
		+
		+	* The kernel startup (just few lines)
		+	KERNELBASE=c0000000 r6=900030 r7=900052
		+	cmd_line=root=/dev/md0 panic=5 BOOTVER=1.24
		+	Memory BAT mapping: BAT2=128Mb, BAT3=0Mb, residual: 0Mb
		+	Linux version 2.4.20_mvl31-ppc_terastation (root@develop) (gcc version 3.3.1 (MontaVista 3.3.1-7.0.13.0500039 2005-01-13)) #3 Tue Jul 18 09:29:11 JST 2006
		+	BUFFALO Network Attached Storage Series
		+	(C) 2002-2005 BUFFALO INC.
		+	On node 0 totalpages: 32768
		+	zone(0): 32768 pages.
		+	zone(1): 0 pages.
		+	zone(2): 0 pages.
		+	Kernel command line: root=/dev/md0 panic=5 BOOTVER=1.24
		+	OpenPIC Version 1.2 (1 CPUs and 10 IRQ sources) at 80040000
		+	decrementer frequency = 32.768000 MHz
		+	Calibrating delay loop... 174.48 BogoMIPS
		+	Memory: 125200k available (1692k kernel code, 532k data, 68k init, 0k highmem)
		+	Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
		+	Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
		+	Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
		+	Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
		+	Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
		+	POSIX conformance testing by UNIFIX
		+	PCI: Probing PCI hardware
		+	Linux NET4.0 for Linux 2.4
		+	Based upon Swansea University Computer Society NET3.039
		+	Initializing RT netlink socket
		+	BUFFALO INC. RTC driver ver 1.00
		+	MICON V2 (C) BUFFALO INC. V.1.00 installed.
		+	MICON ctrl (C) BUFFALO INC. V.1.00 installed.
		+	Kernel event proc (C) BUFFALO INC. V.1.00 installed.
		+	LSP Revision 1
		+	Starting kswapd
		+	Disabling the Out Of Memory Killer
		+	Journalled Block Device driver loaded

Ramuk at 23:45, 11 November 2007

Ramuk — Sun, 11 Nov 2007 23:45:53 GMT

← Older revision		Revision as of 23:45, 11 November 2007
Line 1:		Line 1:
-	{{Template:Articles~~\|Terastation~~\|TerastationProV1}}	+	{{Template:Articles\|TerastationProV1}}

	== What is the Serial Console ==		== What is the Serial Console ==

Ramuk at 18:34, 11 November 2007

Ramuk — Sun, 11 Nov 2007 18:34:37 GMT

← Older revision		Revision as of 18:34, 11 November 2007
Line 1:		Line 1:
-	{{Template:Articles\|Terastation}}	+	{{Template:Articles\|Terastation\|TerastationProV1}}

	== What is the Serial Console ==		== What is the Serial Console ==

Ramuk at 03:39, 11 November 2007

Ramuk — Sun, 11 Nov 2007 03:39:37 GMT

← Older revision		Revision as of 03:39, 11 November 2007
Line 1:		Line 1:
		+	{{Template:Articles\|Terastation}}
		+
	== What is the Serial Console ==		== What is the Serial Console ==
	The serial console is allowing to get message output from the boot process. You can check the boot log (you can even interrupt it to enter some commands), and also the kernel boot log.		The serial console is allowing to get message output from the boot process. You can check the boot log (you can even interrupt it to enter some commands), and also the kernel boot log.

Ramuk: 53 revision(s)

Ramuk — Sat, 10 Nov 2007 18:07:59 GMT

53 revision(s)

← Older revision

Revision as of 18:07, 10 November 2007