Serial port
From NAS-Central Buffalo - The Linkstation Wiki
(Difference between revisions)
m (→Buy a TTL/RS232 or TTL/USB interface) |
m (→Buy a TTL/RS232 or TTL/USB interface) |
||
| Line 50: | Line 50: | ||
! |The cheapest TTL/USB converter uses a chip by FTDI (the same chip is used in the [[SCON-KIT/ PRO quick manual | SCON-KIT]] ) | ! |The cheapest TTL/USB converter uses a chip by FTDI (the same chip is used in the [[SCON-KIT/ PRO quick manual | SCON-KIT]] ) | ||
|- | |- | ||
| - | || [[Image:ET-MINI_RS232_3V.jpg|200px]] | + | |width="350px" | [[Image:ET-MINI_RS232_3V.jpg|200px]] |
| - | || [[Image:MM232R.jpg|200px]] | + | |width="250px" | [[Image:MM232R.jpg|200px]] |
|- | |- | ||
|| This board is made by [http://www.futurlec.com Futurelec], however the order is shipped from Thailand so it takes 2-3 weeks to get it. | || This board is made by [http://www.futurlec.com Futurelec], however the order is shipped from Thailand so it takes 2-3 weeks to get it. | ||
| Line 72: | Line 72: | ||
* $0.60 - [http://www.futurlec.com/Connectors/PLHDPIN.shtml Futurelec: PLHDPIN - Crimp Pin for Header Connector] | * $0.60 - [http://www.futurlec.com/Connectors/PLHDPIN.shtml Futurelec: PLHDPIN - Crimp Pin for Header Connector] | ||
</small> | </small> | ||
| - | |||
| - | |||
| - | |||
| - | |||
|| | || | ||
<small> | <small> | ||
Revision as of 19:48, 3 October 2007
Model Specific Directions
| 
| 
| How to add Serial Access | ||
|---|---|---|---|---|---|
| LS1 | HD-HLAN v1 | .jpg){kind=small} | For the LS1 | ||
| KURO/HG | KUROBOX |  | For Kuro/HG | ||
| HG | HD-HGLAN | | For the HG | ||
| LS2 | HD-HLAN v2 | | For the LS2 | ||
| LSPRO | LS-GL |  | Use Bottom Slot | ||
| KUROPRO | KUROBOX Pro |  | |||
Level Shifter
Build your own TTL/RS232 or TTL/USB interface
- TTL/RS232 - Building a Custom Serial Interface
- TTL/USB - Use a cheap phone sync cable with the serial port
Buy a TTL/RS232 or TTL/USB interface
| The cheapest TTL/RS232 converter uses a MAX232 with two serial channels for standard TTL 3V input. | The cheapest TTL/USB converter uses a chip by FTDI (the same chip is used in the SCON-KIT ) |
|---|---|
| 
|
| This board is made by Futurelec, however the order is shipped from Thailand so it takes 2-3 weeks to get it.
You'll also need some headers and connectors | This cable is made by FTDI, but the pinout at the connector end would need to be reassigned. Spec Sheet w/ pinout, wire colors & other info
You will also need a 4 pin header
|
|
|
|
| Others | Others |
|
|
|
| This disambiguation page lists articles associated with the same title. If an internal link led you here, you may wish to change the link to point directly to the intended article. |
