TS-WX1.0TL/R1
From NAS-Central Buffalo - The Linkstation Wiki
Contents
BUFFALO TS-WX1.0TL/R1 1TB TeraStation Duo
As seen for sale on newegg. [1]
Adding hosts to the TeraStations's hosts file
Confirmed in firmware 1.55
If you directly edit the /etc/hosts file your changes will be over written by the init.d scripts when you reboot. However if you add NFS clients from the web admin interface (even if you do not enable NFS) then they will be added to /etc/melco/nfs_clients and their details will be merged into the hosts file.
cpuinfo
Processor: ARM926EJ-S rev 0 (v5l) BogoMIPS: 956.82 Features: swp half thumb fastmult vfp edsp CPU implementer: 0x41 CPU architecture: 5TE CPU variant: 0x1 CPU part: 0x926 CPU revision: 0 Cache type: write-back Cache clean: cp15 c7 ops Cache lockdown: format C Cache format: Harvard I size: 32768 I assoc: 4 I line length: 32 I sets: 256 D size: 32768 D assoc: 4 D line length: 32 D sets: 256 Hardware: Feroceon-MV78XX0 Revision: 0000 Serial: 0000000000000000
dmesg output
Linux version 2.6.22.18 (root@build2.dd-hot24.nas.buffalo.local) (gcc version 4.2.0 20070413 (prerelease)) #749 Wed Sep 30 21:38:05 JST 2009
CPU: ARM926EJ-S [41159260] revision 0 (ARMv5TE), cr=00053977
Machine: Feroceon-MV78XX0
Using UBoot passing parameters structure
u.mv_uboot.env_addr is 0xfff80000. Using tag's value.
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 131072
DMA zone: 1024 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 130048 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
Built 1 zonelists. Total pages: 130048
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00900040,15M panic=5 BOOTVER=2.06
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512MB 0MB 0MB 0MB = 512MB total
Memory: 499584KB available (4192K code, 321K data, 128K init)
Calibrating delay loop... 956.82 BogoMIPS (lpj=4784128)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
CPU 0, CPU Interface
-------------
SDRAM_CS0.... ....base 00000000, size 512MB
SDRAM_CS1.... ....disable
SDRAM_CS2.... ....disable
SDRAM_CS3.... ....disable
DEVICE_CS0... ....base f8000000, size 32MB
DEVICE_CS1... ....base fe000000, size 1MB
DEVICE_CS2... ....base fc000000, size 1MB
DEVICE_CS3... ....no such
DEV_BOOCS.... ....base fff00000, size 512KB
DEVICE_SPI... ....base fff00000, size 512KB
PEX0_IO...... ....base f2000000, size 8MB
PEX0_MEM0.... ....base c8000000, size 64MB
PEX1_IO...... ....base f3000000, size 8MB
PEX1_MEM0.... ....base cc000000, size 64MB
PEX2_IO...... ....no such
PEX2_MEM0.... ....no such
PEX3_IO...... ....base f5000000, size 8MB
PEX3_MEM0.... ....base d4000000, size 64MB
PEX4_IO...... ....base f6000000, size 8MB
PEX4_MEM0.... ....base d8000000, size 64MB
PEX5_IO...... ....no such
PEX5_MEM0.... ....no such
PEX6_IO...... ....no such
PEX6_MEM0.... ....no such
PEX7_IO...... ....no such
PEX7_MEM0.... ....no such
CRYPT_ENG..... ....base f7000000, size 2MB
INTER_REGS... ....base f1000000, size 1MB
Marvell Development Board (LSP Version 2.0.2_MV78XX0)-- DB-MV78100-A-BP-BUFFALO Soc: MV78100 A0 LE
Detected Tclk 166666667 and SysClk 400000000
Marvell USB EHCI Host controller #0: 808fd600
Marvell USB EHCI Host controller #1: 808fd400
Marvell USB EHCI Host controller #2: 808fd200
PEX0 interface detected no Link.
PEX4 interface detected no Link.
SCSI subsystem initialized
NET: Registered protocol family 2
Time: orion_clocksource clocksource has been installed.
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
RTC registered.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.0.02 installed.
>BuffaloCpuInterrupts_init
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
UPSDRV (C) BUFFALO INC. V.1.00 installed.
OMRON contact type ups shutdown support enabled!
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
Buffalo RTC Driver (C) BUFFALO INC. Ver.1.00 (RS5C372) installed.
Buffalo GPIO SATA Hotplug Event Driver (C) BUFFALO INC. Ver.1.00 installed.
Use the XOR engines (acceleration) for enhancing the following functions:
o RAID 5 Xor calculation
o kernel memcpy
o kenrel memzero
Number of XOR engines to use: 2
cesadev_init(8001237c)
mvCesaInit: sessions=640, queue=64, pSram=f7000000
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
SGI XFS with ACLs, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
io scheduler noop registered (default)
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 12) is a 16550A
serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 13) is a 16550A
serial8250.2: ttyS2 at MMIO 0xf1012200 (irq = 14) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
loop: module loaded
Load Marvell Ethernet Driver
o Cached descriptors in DRAM
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload enabled
o Receive checksum offload enabled
o Transmit checksum offload enabled
o Network Fast Processing (Routing) supported
o Proc tool API enabled
o Rx descripors: q0=128
o Tx descripors: q0=532
o Loading network interface:
eth0 eth1
Network Fast Processing Disabled
mvFpRuleDb (809e0000): 16384 entries, 65536 bytes
Integrated Sata device found
mvSataInitAdapter : regVal changed(0x00000010)
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
** BUFFALO Disable Command Queuing Function [0 0] **
** BUFFALO Disable Command Queuing Function [0 1] **
scsi 0:0:0:0: Direct-Access SAMSUNG HD502HI 1AG0 PQ: 0 ANSI: 5
Linux IAL (ERROR) [0 0 0]: set device max sectors to 2048
scsi 1:0:0:0: Direct-Access SAMSUNG HD502HI 1AG0 PQ: 0 ANSI: 5
Linux IAL (ERROR) [0 1 0]: set device max sectors to 2048
Linux IAL (ERROR) : retry command host=0, bus=0 SCpnt = 9f10bba0
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 sda5 sda6
sd 0:0:0:0: [sda] Attached SCSI disk
Linux IAL (ERROR) : retry command host=1, bus=1 SCpnt = 9f10bba0
sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 23 00 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 23 00 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
SPI Serial flash detected @ 0xfff00000, 512KB (8sec x 64KB)
cmdlinepart partition parsing not available
Write size : 0x00000800
OOB size : 0x00000040
Erase size : 0x00020000
NAND device: Manufacturer ID: 0x20, Chip ID: 0xdc (ST Micro NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 1195 at 0x09560000
Bad eraseblock 1864 at 0x0e900000
Bad eraseblock 2989 at 0x175a0000
cmdlinepart partition parsing not available
Using static partition definition
Creating 2 MTD partitions on "nand_mtd":
0x00000000-0x02000000 : "nboot"
0x02000000-0x20000000 : "nroot"
mice: PS/2 mouse device common for all
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1 116 MB/s
raid6: int32x2 128 MB/s
raid6: int32x4 130 MB/s
raid6: int32x8 98 MB/s
raid6: using algorithm int32x4 (130 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
arm4regs : 824.000 MB/sec
8regs : 742.000 MB/sec
32regs : 822.400 MB/sec
raid5: using function: arm4regs (824.000 MB/sec)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
md: md10 stopped.
md: bind<sdb5>
md: bind<sda5>
raid1: raid set md10 active with 2 out of 2 mirrors
md: md1 stopped.
md: bind<sdb2>
md: bind<sda2>
raid1: raid set md1 active with 2 out of 2 mirrors
md: md0 stopped.
md: bind<sdb1>
md: bind<sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Trying to move old root to /initrd ... okay
Freeing init memory: 128K
Adding 999864k swap on /dev/md10. Priority:-1 extents:1 across:999864k
kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_marvell ehci_marvell.168472: Marvell Orion EHCI
ehci_marvell ehci_marvell.168472: new USB bus registered, assigned bus number 2
ehci_marvell ehci_marvell.168472: irq 17, io base 0xf1051100
ehci_marvell ehci_marvell.168472: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ehci_marvell ehci_marvell.336244: Marvell Orion EHCI
ehci_marvell ehci_marvell.336244: new USB bus registered, assigned bus number 3
ehci_marvell ehci_marvell.336244: irq 18, io base 0xf1052100
ehci_marvell ehci_marvell.336244: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
eth1: started
eth0: link down
eth0: started
eth0: link up, full duplex, speed 100 Mbps
eth0: TxEnable WA - Enabled, deep=1
