Difference between revisions of "Template:Reconnect disk to LS and flash firmware"

From NAS-Central Buffalo - The Linkstation Wiki
Jump to: navigation, search
m (Reconnect disk to LS and flash firmware)
m (Reverted edits by 140.113.152.201 (Talk) to last version by 71.59.39.159)
 
(8 intermediate revisions by 4 users not shown)
Line 1: Line 1:
===Reconnect disk to LS and flash firmware===
+
===Connect disk to LS and flash firmware===
 
* power on LS (Reset button not pressed)
 
* power on LS (Reset button not pressed)
*Flash The [[The LinkStation firmware flasher]], you could flash [[OpenLink]], [[FreeLink]] or the Stock Firmware.
+
*Using [[The LinkStation firmware flasher]], you could flash [[OpenLink]], [[FreeLink]] or the Stock Firmware.
 
*Open the archive and carefully read the included <tt>README</tt> file for any specific instructions.
 
*Open the archive and carefully read the included <tt>README</tt> file for any specific instructions.
 
*Disable any firewall(s), '''including any built-in Windows firewall'''  
 
*Disable any firewall(s), '''including any built-in Windows firewall'''  
 +
*If you are running some '''virus checker or worm detection software''', disable this also
 
*Make sure the LinkStation and your PC are on the same sub-network. This likely requires that you change the IP address (and probably the subnet-mask) of your PC and router to a different IP address in [[EM Mode]] it will have a static IP address of 192.168.11.150 or to connect your PC and LinkStation directly with a crossover cable.
 
*Make sure the LinkStation and your PC are on the same sub-network. This likely requires that you change the IP address (and probably the subnet-mask) of your PC and router to a different IP address in [[EM Mode]] it will have a static IP address of 192.168.11.150 or to connect your PC and LinkStation directly with a crossover cable.
 
*unpack HD-H*.zip (use the proper firmware for your LS)
 
*unpack HD-H*.zip (use the proper firmware for your LS)
Line 17: Line 18:
 
*if You get the following message You are done.
 
*if You get the following message You are done.
 
  The firmware has been renewed
 
  The firmware has been renewed
* But because the reformatting (?)and partitioning takes too long,
+
* But because the reformatting and partitioning takes too long, the Diskfull LED may blink or you can hear the disk being active (withoug LED indication).<br>
the diskfill LED may blink and you may get:
+
Then you will get:
 
  Attempt to renew firmware has failed
 
  Attempt to renew firmware has failed
* if so, wait until Diskfull LED goes off after some minutes.
+
* if so, wait until Diskfull LED goes off or the disk activity stops after some minutes.
 
* press "search" again.
 
* press "search" again.
 
* start update again.
 
* start update again.
Line 37: Line 38:
 
  useradd -m -d /home/guest guest
 
  useradd -m -d /home/guest guest
 
===Reboot===
 
===Reboot===
Place the hard drive in the LinkStation and reboot. Be patient as the first boot may take longer than normal.
+
Be patient as the first boot may take longer than normal.

Latest revision as of 17:33, 4 January 2009

Connect disk to LS and flash firmware

  • power on LS (Reset button not pressed)
  • Using The LinkStation firmware flasher, you could flash OpenLink, FreeLink or the Stock Firmware.
  • Open the archive and carefully read the included README file for any specific instructions.
  • Disable any firewall(s), including any built-in Windows firewall
  • If you are running some virus checker or worm detection software, disable this also
  • Make sure the LinkStation and your PC are on the same sub-network. This likely requires that you change the IP address (and probably the subnet-mask) of your PC and router to a different IP address in EM Mode it will have a static IP address of 192.168.11.150 or to connect your PC and LinkStation directly with a crossover cable.
  • unpack HD-H*.zip (use the proper firmware for your LS)
  • start HD-H*FWUpdate.exe (use the proper updater for your LS)
GeneralFreeLink1.jpg
  • press "search", should find Linkstation "EM" (Emergency Mode)
  • After finding your LinkStation, press the "Renew Firmware" button, and wait. Have patience, and keep your calm. If you think the Firmware updater is acting strange, do not try to disconnect the LinkStation or abort the update in another way.
  • start update, following messages appear:
Settings are being saved
Firmware is being transmitted
LinkStation Firmware has been renewed
Settings are being restored
  • if You get the following message You are done.
The firmware has been renewed
  • But because the reformatting and partitioning takes too long, the Diskfull LED may blink or you can hear the disk being active (withoug LED indication).

Then you will get:

Attempt to renew firmware has failed
  • if so, wait until Diskfull LED goes off or the disk activity stops after some minutes.
  • press "search" again.
  • start update again.
  • after all the other messages You should get this time:
The firmware has been renewed
  • After flashing connect your LinkStation up to the network with subnet 192.168.1.XXX the LS is now reachable via telnet and the "old" IP. so switch back IP settings and reenable the windows firewall.

Login to the LinkStation

  • Find your LinkStation on the network and Telnet to it with PuTTYtel You will be at the root shell prompt:
telnet linkstation
  • set root password:
passwd
  • change bash to login:
vi /etc/init.d/telnet
  • add a new guest user
useradd -m -d /home/guest guest

Reboot

Be patient as the first boot may take longer than normal.